HobbyKing B-17 F, Руководство пользователя

Страница: 8 / 13

H · KING
PRE FLIGHT CHECK
1. Always range check your model before any flight (especially when flying a new model for the
first time). Follow your radio manufacturers guidelines for performing this check.
2. Check all screw/bolts and mounting points are firmly secured, including control horns and
clevises.
3. Only fly with fully charged batteries (both in your radio and model). Failure to do so could result
in loss of control, damage to the model and/or persons/property around you. Check your
batteries are fully charged.
4. With the model powered up (Transmitter on first, then receiver/model) check that all surface
are free from damage/obstructions, moving in the correct directions and freely with stick input.
5. Inspect the model and prop for any damage that may have occurred during transit and listen
for any unusual sounds from the electronics when powered up. If in doubt, do not fly.
6. With the model held securely and the prop free of obstructions, increase the throttle just slightly
to confirm the rotations of the prop is correct. The model should want to pull straight forward
with throttle.
7. If this is your first flight with the model double check the C/G is at the correct position. If not
adjust battery position inside model accordingly.
8. If you are an inexperienced model pilot seek the help and assistance of an experienced pilot
to perform these final checks and to test fly the model for you.
Thank you for purchasing the H-King 8-17.
Long may it serve you.
13
SPARE PARTS GREEN VERSION
1 ) Green fuselage Part No . 9310000283-0
Part No . 9310000284-0
Part No . 9310000285-0
Part No . 9310000286-0
Part No . 9310000287-0
6) Green nose dome Part No . 9310000288-0
2) Green main wing 7) Green ball/belly turret Part No . 9310000289 - 0
3) Green horizontal tail 8) Green battery natch Part No . 9310000290 - 0
4) Green vertical tail 9) Green B-17 'F' decal set Part No . 9310000291 - 0
5) Green cowl set
SPARE PARTS SILVER VERSION
1 ) Silver fuselage
2) Silver main wing
3) Silver horizontal tail
4) Silver vertical tail
5) Silver cow1 set
Part No . 9310000297-0
Part No . 9310000298-0
Part N o . 9310000299-0
Part No . 9310000300-0
Part No . 9310000301-0
COMMON/SHARE PARTS
6) Silver nose dome
7) Silver ball/belly turret
8) Silver battery natch
9) Silver B-17 'G' decal set
Part No . 9310000302-0
Part No . 9310000303-0
Part N o . 9310000304-0
Part No . 9310000305-0
10) Mounting and control accessories Part No . 9310000292-0 13) Proppeller set Part No . B -1 7PNP - PROP
11) Retracts inc struts/wheels Part No . 9310000293--0
12) 900kv motor Part No . 93 1 0000294--0
DECAL APPLICATION GUIDE
14) ESC with full wires Part No . 9310000295-0
Applying the supplied decals will take you longer than assembling the model. This is because
real care must be taken when doing so. Please follow carefully the guidelines below to achieve
the best possible finish on your B-17.
Note:
* The decals supplied are vinyl type decals and are supported on a clear adhesives fronting
film. These require care and attention when applying so please follow the below guidelines
and the techniques outlined for the best results.
1. Study the scheme reference sheet carefully and understand fully where each decal should
be applied (see following pages).
2. Seperate the decal you wish to apply (decals are grouped according to their layout on the
model) from the main sheet. The entire decal sheet (including the paper backing) is pre-cut
for you so you can seperate each group of decals as required.
3. Before lifting from the paper, rub the surface of the clear protective film/fronting to ensure
all of the decal sticks to it. This will ensure the marking lifts fully off the backing paper in
tact.
4. Peel the fronting off of the sheet ensuring the entire decal lifts with it.
5. Position the decals/fronting carefully on the model according to the decal reference sheet
then gently rub (using a dry cloth) the decal in place, rubbing from the center of the decal
outwards, to avoid wrinkles and air bubbles.