background image

Basic Operation   

13

Doc: HMSI-27-262, Rev: 2.10

Anybus X-gateway User Manaul

2.3 Controlling the Gateway from the Network

2.3.1 Control Word

It is possible to control certain aspects of the gateway from the network by setting the corresponding 
bits in the Control Word.

This functionality is disabled by default, but can be enabled separately for each network interface 
through the Gateway Config Interface. Note that if enabled, certain actions may be required in order for 
the gateway to start exchanging data.

Control Word Contents:

• Master  Mode

1

These bits specify the current operation mode of the on-board master from the other network 
(these bits are not available on the master/scanner side).
The exact definition of these bits depend on the network in question, however common for all 
networks is that if the Control Word has been enabled, it is required to specify a value for these 
bits in order for the gateway to start exchanging data.

See also...

- 3-16 “Anybus Configuration Manager”
- Interface addendum for the on board master/scanner.

• Reset

This bit is used to reset the gateway.

1: Restart the gateway and re-initialize both network interfaces.
0: (no action)

See also...

• 2-11 “Status & Diagnostics”
• 3-16 “Anybus Configuration Manager”

2.3.2 Network Specific Controls

Some interfaces may provide additional methods of controlling the gateway from the network. For fur-
ther information, consult the separate interface addendums for your product.

b15

b14

b13

b12

b11

b10

b9

b8

b7

b6

b5

b4

b3

b2

b1

b0

Reset

Master Mode

(MSB)

(LSB)

1. Master configurations only.

Содержание Anybus X-Gateway Series





















Отзывы: