HMS Networks INKNXMBM1000100 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 19

HMS Networks INKNXMBM1000100 Скачать руководство пользователя страница 11

Intesis

TM

KNX

– Modbus Master

User Manual r1.0 eng

© HMS Industrial Networks S.L.U - All rights reserved

This information is subject to change without notice

URL

http

s

://www.intesis.com

11 / 19

4

Connections

Find below information regarding the Intesis connections available.

KNX Port
Connect the KNX TP1 bus to conn and -

of gateway’s KNX Port. Respect the polarity

Port A / Modbus RTU
Connect the EIA485 bus to connectors A2 (A-), A3 (B+) and A1

(SNGD) of gateway’s Port A. Respect the polarity.

Note for Port A; Remember the characteristics of the standard EIA485 bus: maximum distance of 1200 meters ,
maximum 32 devices connected to the bus, and in each end of the bus it must be a termination resistor of 120 Ω.
The gateway has an internal bus biasing circuit that incorporates the termination resistor. If you install the gateway
in one of the ends of the bus, then do not install an additional termination resistor in that end.

«
...
9
10
11
12
13
...
»

Содержание INKNXMBM1000100




















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды