background image

This section describes how to operate your newly configured PRO850 system, assuming the factory default 
settings. If you used other existing settings rather than factory defaults, you will need to refer to the PRO850 
Operating Instructions for information regarding those settings. 

 

BELTPAC OPERATION 

Refer to the figures below for the functions of the various controls in the default configuration. The functions of 
the buttons are configurable and may be different if you are not using default settings. 

Controls, Indicators, and Buttons 

 

 

 

 

 

 

 

 

 

 

 

 

1.  Master On/Off Volume Control 

Turns Beltpac on and off. 
Controls volume levels and beep intensity. 
Press and hold control button in to mute primary receiver input.  

2. PWR/BATT 

Indicator 

Remains lit when power is on.   
Green = good batteries 
Amber = low batteries 
Red = nearly dead batteries 

3. Transmit 

Indicator 

On red when Beltpac is transmitting. Default mode is PTE – transmitter on continuously 

4.  A Button (Talk Channel 1) 

Press and release button in less than one second to lock on talk on channel 1. Only Beltpacs listening to 
channel 1 will hear you. 
Press and hold for momentary function, to remain on only while button is held.  
This button only works if the B indicator is not red.

 

5.  A Channel Indicator (Channel 1) 

Green while listening to channel 1 and red while talking on channel 1. 

6.  B Button (Talk Channel 2) 

Press and release button in less than one second to lock on talk on channel 2. Only Beltpacs listening to 
channel 2 will hear you. 
Press and hold for momentary function, to remain on only while button is held.  
This button only works if the A indicator is not red. 

SECTION 4.  PRO850 OPERATION 

4

12 

10 

6

11 

5

7

Содержание PRO850














Отзывы: