HLA BR Series Скачать руководство пользователя страница 16

Страница: 16 / 20

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

SOLUTION

Brush slows or stops when
sweeping

Travel speed too fast

Travel no more than 5 mph (8kph) while
sweeping

Trying to sweep too much
material at once

Make several passes with Broom

Relief pressure set too low

Set relief pressure to 2000 psi (138.0 bars)

Pump has failed

Contact dealer to repair or replace

Filter plugging

Change or clean filter

Hydraulic motor is failing

Test hydraulic system

Dirt or debris in spools

Contact your dealer or HLA

Brush head assembly “bounces”
during sweeping

Travel speed too fast and/or
brush speed too slow

Find correct combination of ground
and brush speeds: do not travel at
more than 5 mph (8 kph)

Core is bent

Replace core

Brush wears into cone shape

Broom is not level

Level Broom before each use

Tires on power unit at different
pressures or are different sizes

Check tire sizes and rating; make
corrections as necessary

Brush wears very quickly

Brush pattern too wide

Adjust brush pattern 2-4 inches
(5-10cm)

Hydraulic drive motors
malfunctioning

Low hydraulic fluid level

Check and replenish hydraulic fluid.

Improper hose hookup

Check and correct hydraulic hose
connections.

Broken hydraulic line

Check for leaks and replace line.

Jammed brush

Remove interference.

Quick disconnect coupler(s) are
not connected or “Flow Check”

Check coupler connections.
Replace coupler(s) if necessary.

Hydraulic hose blockage

Check for evidence of damage to hoses
that would block flow of oil between
cylinders and control valve.

Hydraulic fluid leaking past seals

Replace seals.

Drum operates in wrong
direction relative to control valve
lever position

Hydraulic hoses connected
incorrectly

Correct hydraulic hose connections.

Aeration of hydraulic fluid
(

generally indicated by foamy

appearance of fluid

Low hydraulic fluid level

Check and refill hydraulic system to proper
level.

Hydraulic fluid foaming due to
improper hydraulic oil usage

Refer to Power Unit’s manual and replace
hydraulic oil using recommended hydraulic
oil.

Содержание BR Series





















Результаты поиска

Содержание BR Series

Отзывы:

Похожие инструкции для BR Series

Бренды по названию

Популярные бренды

HLA BR Series, Руководство оператора

Результаты поиска

Содержание BR Series

Отзывы:

Похожие инструкции для BR Series

Бренды по названию

Популярные бренды