background image

- 9 -

Brush Pattern 

To check pattern:

 

1.

Move Broom to a dusty flat surface.

2.

Set power unit’s parking brake and leave the engine running.

3.

Start the Broom at a slow speed; then lower it so bristle tips and castor wheel touch the ground. The heal of the
bucket should be approximately 1 inch off the ground. Run the Broom in a stationary position for 10-30 seconds.

4.

Raise the Broom and back away; switch off Broom and engine, remove safety restraints and remove the key. The
brush pattern left in the dust should be 2-4 inches (50-133mm) wide, running the length of the Broom.

5.

The castor wheel should just touch the surface, as it is only for leveling purposes.

6.

If the brush pattern is not 2"- 4" wide the broom height needs to be adjusted. Remove 

front bolt from “Broom Mount

Plate” on both ends of broom. Move up or down to achieve proper height, and reinstall bolts.

7.

Adjust the front and side flaps to contact the sweeping surface lightly and evenly.

BROOM HYDRAULIC CONNECTION 

1.

Disconnect  the  hydraulic  hose  quick  couplers  from  one  another  and  attach  the  quick  couplers  to  your  power  unit  as  per  the
instructions in your power unit’s operator’s manual.

2.

Carefully raise the loader arm and cycle the tilt cylinders to check hose clearances and to check any interference.

SAFETY FIRST!! READ AND UNDERSTAND THE SAFETY INSTRUCTIONS 

(pages 3-6 

of this manual)

 BEFORE BEGINNING ANY HYDRAULIC CONNECTION. 

Содержание BR Series





















Отзывы: