background image

 

26

 

MM06UE01-2002 

Table 8.1 

Fault table (continued)

 

Fault 

Possible cause 

Remedy 

The forcer jerks while 

moving and generates 

operating noise that is not 

caused by the profile 

guideways 

EMC interference in the encoder 

signal, encoder cable plug 

connection defective, pin bent in 

plug 

Place motor cable and/or encoder cable 

shield in full contact with the earthing 

terminal of the amplifier, check pin in plug 

Position discrepancies after 

several hours of operation 

 

Use mains filter to stabilize voltage 

 

9.  Disposal 

ATTENTION!

 

 

Danger caused by environmentally hazardous substances! 

The danger to the environment depends on the type of substance used. 

 

Clean contaminated parts thoroughly before disposal! 

 

Clarify the requirements for safe disposal with disposal companies and, where appropriate, with 

the competent authorities! 

 

Table 9.1 

Disposal

 

Fluids

 

Lubricants 

dispose of as hazardous waste in an environmentally friendly way 

Soiled cleaning cloths 

dispose of as hazardous waste in an environmentally friendly way 

Linear motor system

 

Cabling, electrical components 

dispose of as electrical waste 

PP components (e.g. cable chain) 

dispose of separately 

Steel components (e.g. guideways) 

dispose of separately 

Aluminum components (e.g. base) 

dispose of separately 

 
 

 

Содержание SSA






























Отзывы: