Hitachi WH 9DMR Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 47

Hitachi WH 9DMR Скачать руководство пользователя страница 10

--- 7 ---

Overcharge prevention circuit:
A thermostat monitors the surface temperature of the battery and, on detecting the
temperature rise which occurs on completion of charging, automatically turns off the
unit to prevent the battery from overcharge.
Input capacity: 70 W
Indication method: Pilot lamp indicator of battery charging
Function: On

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

During charging

Off

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

Charging completed

*

1

: In the case of tapping screws and wood screws, a minimum of M3 (1/8") is possible.

*

2

: This torque is based on tightening an M12 (15/32") bolt (strength grade: 12.9) for 3 seconds with a hexagonal socket.

*

3

: This torque is based on tightening an M12 (15/32") bolt (strength grade: 12.9) for 3 seconds with a hexagonal socket.

*

4

: Main body does not include accessory tools and hook (hexagonal bit etc.).

Charger (Model UC 18YG)

Prior to charging

During charging

Charging completed

Charging not
possible

High battery
temperature

Blinks

Lit

Blinks

Flickers

Lit

0.5 sec ON, 0.5 sec OFF

Stays ON constantly

0.5 sec ON, 0.5 sec OFF

0.1 sec ON, 0.1 sec OFF

Stays ON constantly

Pilot lamp indications (Model UC 14YFA)

Red pilot lamp
remains lit or flashes.

Green pilot lamp is lit.

Storage battery or charger
is faulty.

Charging not possible
because storage battery
temperature is too high.

NOTE: The Model UC 18YG

charger is exclusive to

NiCad batteries.

«
...
8
9
10
11
12
...
»

Содержание WH 9DMR
















































Отзывы:

Нет отзывов