Hitachi WH 12DH Скачать руководство пользователя страница 22

Страница: 22 / 41

--- 19 ---

8. PRECAUTIONS IN SALES PROMOTION

8-1. Safety Instructions

In the interest of promoting the safest and most efficient use of these tools by all our customers, it is very

important that at the time of sale the salesperson carefully ensures that the buyer seriously recognizes the

importance of the contents of the Handling Instructions, and fully understands the meaning of the precautions

listed on the Caution Plate and Name Plate attached to each tool.

A. Handling Instructions

Salespersons must be thoroughly familiar with the contents of the Handling Instructions in order to give pertinent

advice to the customer. In particular, they must have a thorough understanding of the precautions in the use of

the cordless (battery charger type) electric power tools which are different from those of ordinary electric power

tools

(1) Before use, ensure that the unit is fully charged.

New units are not fully charged. Even if the units were fully charged at the factory, long periods without use,

such as during shipping, cause the storage battery to lose its charge. Customers must be instructed to fully

charge the unit prior to use.

(2) When charging storage batteries, use only the exclusive Model UC 14YF or UC 14YF2 Charger provided with

the tool. Because of the designed rapid-charging feature (about one hour), use of other battery chargers is

hazardous.

(3) Follow prescribed steps in using the charger.

First connect the EB 12 Storage Battery to the Model UC 14YF or UC 14YF2 Charger, then plug the charger

into an AC outlet (ensuring that the voltage matches that indicated on the unit). If this order is reversed, the

charger may not function properly.

(4) Ensure the power source voltage is the same as that indicated on the Name Plate of the charger. Use of any

other power source (DC outlet, fuel powered generator, etc.) will cause the charger to overheat and burn out.

(5) Do not use any voltage increasing equipment (transformer, etc.) between the power source and the charger.

If the charger is used with voltage over and above that indicated on the unit, it will not function properly.

(6) Conduct battery charging at an ambient temperature range of 0 C --- 40 C (32 F --- 104 F).

Special temperature sensitive devices are employed in the charger to permit rapid charging. Ensure that

customers are instructed to use the charger at the indicated ambient temperature range. At temperatures

under 0 C (32 F), the thermostat will not function properly, and the storage battery may be over-charged.

At temperatures over 40 C (104 F), the storage battery cannot be sufficiently charged. The optimum

temperature range is 20 C --- 25 C (68 F --- 77 F).

(7) The battery charger should not be used continuously.

At high ambient temperatures, if over three storage batteries are charged in succession, the temperature of

the coils on the transformer will rise and there is a chance that the temperature fuse inserted in the interior of

the transformer will inadvertently melt. After charging one battery, please charge the next battery after about a

fifteen-minute interval.

(8) The charger case is equipped with air vents to protect the internal electronic components from overheating.

Caution the customer not to allow foreign materials, such as metallic or flammable objects, to be dropped or

inserted into the air vents. This could cause electrical shock, fire or other serious hazards.

Содержание WH 12DH










































Результаты поиска

Содержание WH 12DH

Отзывы:

Похожие инструкции для WH 12DH

Бренды по названию

Популярные бренды

Hitachi WH 12DH, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание WH 12DH

Отзывы:

Похожие инструкции для WH 12DH

Бренды по названию

Популярные бренды