Hitachi VSP E590 Скачать руководство пользователя страница 16

Страница: 16 / 18

Before you begin

Make sure the storage system is connected to your production network.

Procedure

1. Connect the Fibre Channel data ports on each storage system controller to your Fibre Channel switch.

2. Connect your Fibre Channel switch to the Fibre Channel HBA card in each host computer or server.

Connecting iSCSI ports to hosts

Each controller supports 10-gigabit Ethernet copper (RJ-45) or optical (fiber) iSCSI connectivity to your data network.

Important Before connecting the storage system to a host, review the requirements and detailed instructions in the

Open-Systems Host Attachment Guide

Before you begin

Make sure the storage system is connected to your production network.

Procedure

1. Using the appropriate cable, connect the iSCSI data ports on each storage system controller to your Gigabit

Ethernet network switch.

2. Connect your Gigabit Ethernet network switch to the NIC or HBA card in each host computer or server.

Step 8: Register your storage system with Hitachi Vantara Support

If you do not already have an account on the

Support Website

, you will need to

. Otherwise, you will not be able

https://knowledge.hitachivantara.com/Documents/Storage/VSP_E_Series/93-04-0x/Installation/Installing_your_VSP_E590_an…

Updated: Thu, 06 Jan 2022 00:49:25 GMT

Содержание VSP E590



















Результаты поиска

Содержание VSP E590

Отзывы:

Похожие инструкции для VSP E590

Бренды по названию

Популярные бренды

Hitachi VSP E590, Установка

Результаты поиска

Содержание VSP E590

Отзывы:

Похожие инструкции для VSP E590

Бренды по названию

Популярные бренды