Hitachi RAI-25NH5 Скачать руководство пользователя страница 51

Страница: 51 / 62

– 61 –

SERVICE CALL Q & A

Model

RAI-25NH5
RAI-35NH5

COOLING MODE

The compressor has
stopped suddenly during
cooling operation.

Sound of running water is heard from
indoor unit during dehumidifying.

Compressor occasionally does not
operate during dehumidifying.

The circulation stops
occasionally during
Heating mode.

When the fan speed is set
at HIGH or MED, the flow
is actually Weak.

Heating operation stops
while the temperature is
preset at "30".

Check if the indoor heat
exchanger is frosted.
Wait for 3-4 minutes
until it is defrosted.

If the air conditioner operates
in cooling mode when it is
cold, the evaporator may get
frosted.

Normal sound when refrigerant flows in pipe.

Compressor may not operate when room
temperature is 10

C or less. It also stops

when the humidity is preset humidity or less.

It occurs during defrost-
ing. Wait for 5-10
minutes until the
condenser is defrosted.

At the beginning of heating,
the fan speed remains
LOW for 30 seconds. If
HIGH is selected, it
switches to LOW and again
to MED after additional 30
seconds.

If temperature is high in
the outdoor, heating
operation may stop to
protect internal devices.

DEHUMIDIFYING MODE

HEATING MODE

Содержание RAI-25NH5































































Результаты поиска

Содержание RAI-25NH5

Отзывы:

Бренды по названию

Популярные бренды

Hitachi RAI-25NH5, Руководство по обслуживанию

Результаты поиска

Содержание RAI-25NH5

Отзывы:

Бренды по названию

Популярные бренды