Hitachi RAI-25NH5 Скачать руководство пользователя страница 17

Страница: 17 / 62

– 15 –

FAN SPEED (AUTO)

..... When the AUTO fan speed mode is set in the cooling/heating operation:

For the heating operation

●

The fan speed will automatically change according to the temperature
of discharged air.

●

When the difference of room temperature and setting temperature is
large, fan starts to run at HI speed.

●

When the room temperature reaches setting temperature, fan speed
changes to LOW automatically.

●

When the difference of room temperature and setting temperature is
large, fan starts to run at HI speed.

●

After room temperature reaches the preset temperature, the cooling
operation, which changes the fan speed and room temperature to obtain
optimum conditions for natural healthful cooling will be performed.

For the cooling operation

FAN OPERATION

You can use the device simply as an air circulator. Use this function to dry the interior of the indoor
unit at the end of summer.

Press the FUNCTION selector so that the display indicates
(FAN).

Press the (FAN SPEED) button.

Press the (START/STOP) button. Fan operation starts with
a beep. Press the button again to stop operation.

START

STOP

RESET

Содержание RAI-25NH5































































Результаты поиска

Содержание RAI-25NH5

Отзывы:

Бренды по названию

Популярные бренды

Hitachi RAI-25NH5, Руководство по обслуживанию

Результаты поиска

Содержание RAI-25NH5

Отзывы:

Бренды по названию

Популярные бренды