manualshive.com logo in svg

Hitachi RAD-25NH4, Руководство по установке, Страница: 19 / 20

Поделиться
Скачать
Hitachi RAD-25NH4 Скачать руководство пользователя страница 19

– 19 –

ENGLISH

DEUTSCH

FRAN

Ç

AIS

IT

ALIANO

SP

ANISH

POR

TUGU

Ê

S

∂ÏÏËÓÈο

Р

УССКИЙ

1

2

Check to see if the unit’s earth line has been connected
correctly.

If the earth line is disconnected or faulty, unit failure or electric
shock hazard may result.

Check to see if the mounting frame has rusted excessively
or if the outdoor unit has tilted or become unstable.

It could collapse or fall, causing injury.

WHEN ASKING FOR SERVICE, CHECK THE FOLLOWING POINTS.

CONDITION

CHECK THE FOLLOWING POINTS

• Do the batteries need replacement?
• Is the polarity of the inserted batteries correct?

• Is the air filter blocked with dust?
• Is the set temperature suitable?
• Have the top and bottom air deflectors been adjusted to their correct

positions according to the operation mode selected?

• Are the air inlets or air outlets of indoor and outdoor units blocked?
• Is the fan speed “LOW”?

WARNING

WARNING

AFTER SALES SERVICE AND WARRANTY

• Is the fuse all right?
• Is the voltage extremely high or low?
• Is the circuit breaker “ON”?
• Is the setting of operation mode different from other indoor units?

When it does not operate.

When it does not cool well.
When it does not heat well.

If the remote controller is not
transmitting a signal.

(Remote controller display is
dim or blank.)

REGULAR INSPECTION

PLEASE CHECK THE FOLLOWING POINTS EVERY EITHER HALF YEARLY OR YEARLY. CONTACT YOUR
SALES AGENT SHOULD YOU NEED ANY HELP.

■

The following phenomena do not indicate unit failure.

Hissing or fizzy sounds

Refrigerant flow noise in the pipe or valve sound generated when flow rate is
adjusted.

Squeaking noise

Noise generated when the unit expands or contracts due to temperature
changes.

Rustling noise

Noise generated with the indoor unit fan’s rpm changing such as operation start
times.

Clicking noise

Noise of the motorized valve when the unit is switched on.

Changing operation noise

Operation noise changes due to power variations according to room temperature
changes.

Mist emission

Mist is generated as the air within the room is suddenly cooled by conditioned
air.

Steam emitted from the outdoor unit

Water generated during defrosting operation evaporates and steam is emitted.

Odors

Caused as the smells and particles of smoke, food, cosmetics, etc. present in
room air become attached the unit and blown off into the room again.

Perking noise

Noise of the ventilation fan sucking in air present in the drain hose and blowing out
dehumidifying water that had accumulated in the condensed water collector. For
details, consult your sales agent.

Содержание RAD-25NH4





















Отзывы:

Нет отзывов