manualshive.com logo in svg

Hitachi RAD-25NH4, Руководство по установке, Страница: 17 / 20

Поделиться
Скачать
Hitachi RAD-25NH4 Скачать руководство пользователя страница 17

– 17 –

ENGLISH

DEUTSCH

FRAN

Ç

AIS

IT

ALIANO

SP

ANISH

POR

TUGU

Ê

S

∂ÏÏËÓÈο

Р

УССКИЙ

MAINTENANCE

  WARNING

• Before cleaning, stop unit operation with the remote controller and turn off the circuit breaker.

  CAUTION

• Do not expose the unit to water as it may cause an electric shock.
• For cleaning inside the air conditioner, consult your sales agent.
• Avoid using detergent when cleaning the heat exchanger of the indoor unit. Unit failure may result.
• When cleaning the heat exchanger with a vacuum cleaner, make sure to wear gloves so as not to injure your

hands on the heat exchanger fins.

1. AIR FILTER

Clean the air filter, as it removes dust inside the room.
Be sure to clean the filter once every two weeks so as not to consume
electricity unnecessarily.

PROCEDURE

Remove suction grille before removing filter.
• Lift up one side of suction grille and remove by inclining it (refer

to diagram).

• Press claw downward to remove filter.

1

Remove dust from the filter using a vacuum cleaner.
If there is too much dust, use neutral detergent. After using neutral
detergent, wash with clean water and dry in the shade.

2

Install the filters.
Slightly lift the suction grille and close as original state.

3

 CAUTION

• Do not wash with hot water at more than 40°C. The filter may shrink.
• When washing it, shake off moisture completely and dry it in the shade; do not expose it directly to the sun.

The filter may shrink.

• Do not operate the air conditioner with the filter removed. Dust may enter the air conditioner and cause

trouble.

Suction grille

Filter

Suction grille

Claw

Lift up suction grille

2. CLEANING OF SUCTION GRILLE

• Wipe it with a soft dry cloth.
• When it is excessively dirty, wipe with soft cloth soaked in lukewarm water or neutral detergent. Then wipe

thoroughly with a soft dry cloth.

 CAUTION

• Never clean with hot water (above 40°C), benzine, gasoline, acid, thinner or a

brush, because it will damage the plastic surface and the coating.

3. MAINTENANCE AT BEGINNING OF LONG OFF PERIOD

• Running the unit setting the operation mode to 

(FAN) and the fan speed

to HI for about half a day on a fine day, and dry the whole of the unit.

• Turn off the circuit breaker.

Air blow

BENZINE

THINNER

A
C

I

D

Содержание RAD-25NH4





















Отзывы:

Нет отзывов