manualshive.com logo in svg

Hitachi RAD-25NH4, Руководство по установке, Страница: 16 / 20

Поделиться
Скачать
Hitachi RAD-25NH4 Скачать руководство пользователя страница 16

– 16 –

Install the new batteries.
The direction of the batteries should match the marks in
the case.

Remove the cover as shown in the figure and remove
the old batteries.

HOW TO CHANGE THE BATTERIES IN THE REMOTE CONTROLLER

2

 CAUTION

1. Do not mix new and old batteries, or different type of

batteries together.

2. Remove the batteries when you do not use the remote

controller for 2 or 3 months.

1

Push and pull to
the direction of
arrow mark 

▼

.

Cover

TEMPORARY SWITCH

Use the temporary switch when operation cannot be done with
the remote controller.
1. By pressing the temporary switch, the operation is done in

previously set operation mode.
When the operation is done using the temporary switch after
the power source is turned off and turned on again, the operation
is done in automatic mode.

2. When the operation is stopped or when the operation is done

with the remote controller again. Press the temporary switch
once again.

●

TEMPORARY
SWITCH

CIRCUIT BREAKER

When you do not use the room air conditioner, set the circuit breaker to “OFF”.

HOW TO USE THE AIR CONDITIONER EFFECTIVELY

1. An average room temperature setting is probably the best for you as well as being

economical.

• Excessive cooling or heating is not recommended for health reasons. High electricity

bills may also result.

• Close the curtains or blinds to prevent heat from flowing into or escaping the room as

well as to make more effective use of electricity.

2. At intervals, the doors and windows should be opened to let fresh air in.

 

CAUTION

Make sure the room is ventilated when operating the air conditioner
at the same time as other heating appliances.

3. Using the timer is recommended before going to sleep or going out.

4. The following must never be used for cleaning the indoor and outdoor units:

• Benzine, thinner and scrub can damage plastic surfaces or coating.
• Hot water above 40°C can shrink the filter and deform plastic parts.

5. Do not block the air intake and air outlet.

• Do not block the air outlets and intakes of the indoor and outdoor units with curtains

or other obstacles which could degrade air conditioner performance and cause unit
failure.

Содержание RAD-25NH4





















Отзывы:

Нет отзывов