Hitachi RAC-50FPA, Руководство по обслуживанию

Страница: 10 / 101

ENGLISH
– 6 –
PREP
ARA
TION BEFORE OPERA
TION
1.
Slide the cover to take it of
f.
2.
Install two dry batteries
AAA.LR03 (alkaline).
The direction of the batteries should match the marks in the case.
1.
Choose a place from where the signals can reach the unit.
2.
Fix the remote controller holder to a wall, a pillar or similar location with the provided screws.
3.
Place the remote controller in the remote controller holder
.
Remote controller Screws
Remote controller holder
Ƶ
T
o
i
n
s
ta
ll
the batteries
3.
Replace the cover at its original position. Ƶ
T
o
fi
x the remote c
o
n
tr
o
ll
e
r holder to the wall
NOTE
Notes on batteries
ƽ
When replacing the batteries, use batteries of the same type, and replace both old batteries together
.
ƽ
When the system is not used for a long time, take the batteries out.
ƽ
The batteries will last for approximately 1 year
. However
, if
the remote controller display begins to fade and degradation of reception performance occurs within a year
, replace both
batteries with new size
AAA.LR03 (alkaline).
ƽ
The attached batteries are provided for the initial use of the system. The usable period of the batteries may be short depending on the manufactured date of the air conditioner
.
Notes on the remote controller
ƽ
Never expose the remote controller to direct sunlight.
ƽ
Dust on the signal transmitter or receiver will reduce the sensitivity
. Wipe of
f dust with soft cloth.
ƽ
Signal communication may be disabled if an electronic- is in the room. Consult the shop if that is the case.
ƽ
If the remote controller signals happen to operate another appliance, move that appliance to somewhere else, or consult the service shop.
ƽ
When the remote controller is not in use, please close the
slide cover to prevent failure.
– 7 –
PREP
ARA
TION BEFORE OPERA
TION
Ƶ
T
o
set calendar and clock
1.
Press
(RESET) button when first time setting.
"Y
ear" blinks.
2.
Press
(TIME) button to set the current year
.
3
. Press
(CLOCK) button. Next, "Day" and
"Month" blink.
4.
Press
(TIME) button to set the current day and
month.
5.
Press
(CLOCK) button. Next, "CLOCK" blinks.
6.
Press
(TIME) button to set the clock to the current
time.
7.
Press
(CLOCK) button.
Calendar and clock are set.
T
o
modify the calendar and clock, press
(CLOCK)
button. Then follow steps 1 to 7. Calendar and
clock shall be set again after
changing
batteries. After changing the batteries, 1.
Press
(RESET) button.
2
.
Direct remote control towards indoor
unit and
pr
s
s
e
(INFO) button.
3
.
The calendar and clock
from indoor unit
will be transmitted
.
Ƶ
Calendar and clock will not be transmitted from indoor unit when the following occurs:
ƽ
When there is a power failure.
ƽ
When breaker
is OFF by user
(unit
is
not
in
ST
ANDBY
MODE).
NOTE
Note on setting the calendar and clock.
ƽ
If the calendar and clock are not set, the ON-timer
, OFF-timer and W
eekly
T
imer cannot be set.
ƽ
If the calendar and clock are not set correctly
, the ON-timer
, OFF-timer and W
eekly
T
imer will not
operate correctly
.
ƽ
When the ON-timer
, OFF-timer and W
eekly
T
imer are set, the calendar and clock cannot be changed. If
need to change the calendar and clock, ON-timer
, OFF-timer and W
eekly
T
imer need to be cancelled.
10