53
Troubleshooting / Replacement Parts
Temperature setting
MIN MID-
MIN
MID MID-
MAX
MAX
Replacement of the vacuum packing
●
If vacuum state can no longer be maintained due to damage,
deformation or a change in color, please replace it with a new one.
●
Part number for each refrigerator model
TROUBLESHOOTING/REPLACEMENT PARTS
REPLACEMENT PARTS
The electric supply failed
The refrigerator is not expected
to use for a long term
Remove frost
Transporting and moving care
When you want
to adjust the
temperature
more fi nely
When you want
to lower the
setting of the
condensation
prevention
heater (the swing
partition and the
partitioning iron
plates)
●
Reduce the number of times of opening and closing the door and avoid storing food additionally until the electric supply is restored.
●
Unplug the power plug and maintain the inner of the refrigerator and the Automatic Ice Maker, and leave all
the door open to dry the refrigerator for 2
〜
3 days.
Pg.41, 49
〜
50
●
Any operation to remove frost is not required because this refrigerator remove frost automatically.
Thawed water is collected in the evaporating tray and automatically evaporates.
●
See
“
Transporting your refrigerator (transport for moving)
”
Pg.35
Temperature settings for Refrigerator, Freezer and Vegetable Compartments can
be adjusted more fi nely than the three levels:
弱
(MIN) ,
中
(MID) and
強
(MAX) .
1. Open the Lower Freezer Door.
2. Push and hold the
button on the Control Panel for fi ve seconds or
more until one beep sounds (This allows fi ner adjustment.)
3. Adjust the
,
or
button to make an adjustment. The temperature
becomes higher by one level every time you push the button. (Pushing
強
(MAX) returns to
弱
(MIN) .)
4. If you want to stop the fi ne adjustment, perform the operation of 1 and 2.
Two beeps sound and You can set the temperature by normal step.
●
A lower setting of the condensation prevention heater will reduce power consumption.
The setting has two levels: 1 and 2. The level 2 achieves a higher reduction in power consumption. A lower setting of the condensation prevention
heater may cause dew condensation in the swing partition or the partitioning iron plates when humidity is high. When dew is formed, cancel the setting.
●
The setting will be cancelled when the power plug is connected and disconnected or power failure recovery takes place.
To cancel the setting, perform the same operation at Level 2.
Alarm is raised (two beeps sound) to cancel the setting.
●
Setting the swing partition
1. Open the Lower Freezer Door.
2. Press and hold the
button on the Control Panel with the refrigerator
doors closed for three seconds or more until one beep sounds. (Level 1)
3. Press and hold the
button on the Control Panel for three seconds or
more until two beeps sound. (Level 2)
4. Close the lower Freezer Door.
●
Setting the partition plate
1. Open the door of the lower freezer
2. With the door of the Refrigerator Compartment closed, push and hold the
button on the control panel for 3 seconds or longer until it beeps (Level 1).
3. Push and hold the
button on the control panel for 3 seconds or longer
until it beeps (Level 2).
4. Close the door of the Refrigerator Compartment.
Hole (inside of the door)
Level 1 for saving electricity
Level 2 for saving electricity
Deactivate
When replacing the following parts, make sure to tell your dealer the type name and buy the special parts.
Replacing the water fi lter
●
Replace the water fi lter when it becomes old.
(Replace it normally once 3
〜
4 years.)
●
Ordering the replacement water fi lter
Tell your dealer the parts number: RJK-30 to buy the
replacement water fi lter. (Ice making capacity is the
same with the water fi lter removed.)
When this happens
Please check. This is the cause.
Others
Swing
partition
Partitioning
iron plates
(six door type only)
You feel electricity a little when touching
the main body of the refrigerator
There is a small hole
inside the door
Radio and/or television
are disturbed by noises
There are thin lines like
scratches on the plastic parts
The Control
Panel is unlit.
There are waving and/or distortions
on the door surface, the side and the
top surface of the refrigerator.
●
The refrigerator may be charged with static electricity, but there is no problem with the safety.
→
It is recommended to ground if you want to remove it.
Pg.35
●
This hole is used to escape the air inside when fi lling the heat insulation material into the
door during the production process. It is neither a fl aw nor abnormal thing.
●
It is caused by the electromagnetic radiation slightly generated from this refrigerator.
→
Install the refrigerator away from the television, radio and interphone.
→
It is recommended to connect the power plug to the power outlet separated from the antenna terminal and
ground the refrigerator.
Pg.35
●
Those lines are caused by the liquid resin fl owing when plastic is molded.
They are especially conspicuous for the transparent parts, but there is no problem with the strength and they
can never lead to any cracks.
●
Approximately two minutes after the end of operation, indicator lamps, excluding
急冷凍
(Quick Freezing) ,
急冷藏
(Quick Cooling) ,
節電
(Energy Saving) ,
急速製冰
(Quick Ice Making) ,
給水
(Water Supply) and eco Operation , become unlit for energy saves.
●
Slight waving and/or distortions are generated in the manufacturing process of the refrigerator.
They may be conspicuous according to the position of the light source and/or the brightness etc., but there is
no problem with the performance.
Long beep
Long beep
Long beep
2 beeps
Push this button for more than 3 seconds
Push this button for more than 3 seconds
Display ON
1 beep
About 3
seconds
Long beep
Long beep
1 beep
About 3
seconds
Parts number
Type: R-SF62BMJ
Type: R-S51BMJ
R-A6200 321
R-S50AM 321
Type: R-SF58BMJ, R-SF48BMJ
R-S59BMJ, R-S49BMJ
R-A5700 321