40
故障了嗎﹖
故障了嗎﹖
故障了嗎﹖
故障了嗎﹖
TROUBLESHOOTING
TROUBLESHOOTING
TROUBLESHOOTING
( )
24
頁
( )
12
頁
冰塊是否放太久了?
有無頻繁開啟箱門.打開箱門的時間
過久?
有無停電?
冰塊變圓.
變小.黏著
在一起
突起
這個時候
檢查項目
原因
When this happens
Please check
Cause
Is there a blackout?
Has the ice been left stored for a long time?
Has the door been opened frequently
or left open for a long time?
Ice cube are
round, small,
joined
together
冰塊的大小
不變
製冰設定剛結束時,冰塊的大小是不會馬上變的。
給水槽內的水量變少的話,就不
能製出大塊的冰。
往給水槽內注水。
是否沒有調整好平行調整。
沒有調整好平行整的調話,就製不出平均
大小的冰塊。
冰塊融化了。
冷凍室不夠冷的時候就不能結冰。
冷凍室不夠冷的時候就不能結冰。
有時候當給水槽內沒水了,或者注水後剛開始做好的冰塊也會發生相互連結或變小。
冰塊粘連時,請用附屬的冰鏟加以分開。
是否已卸除淨水濾片?
放在正確的位置上。
Install the water filter in the correct position.
Pg. 32
( )
32
頁
冰塊有異味
Has the Water Filter been removed?
Ice smells bad
給水槽的水放太久了?
為了防止滑與污垢,每周清洗一次給水槽。
( )
32
頁
Is the water in the Water Supply Container
old?
Pg. 32
To prevent generation of slime and water stain,
wash the water supply container with water once
a week.
要做出一樣大小的冰塊時後,製冰盒有這樣的水路設計,這樣的水路設計會使做出
來的冰塊前端會產生突起狀。
When the water in the water supply container runs out and has just been filled, the first ice
to come out of the machine may be joined together or small.
If ices cubes are joined, separate them with the provided ice scoop.
Water passage is made on the ice tray to make ice cubes of uniform size.
This water passage makes projection at the end of ice cube.
冰塊變圓.
變小.黏著
在一起
Ice cube are
round, small,
joined
together
Size of ice
cannot be
changed
Size of ice may not change immediately after the setting of the large ice cube making
is changed.
Projection
“Larger” size of ice may not be
made if the water level in the water
supply container is low.
Pg. 24
Pg. 12
Add water in the water supply container.
Is horizontal adjustment made
properly?
Is horizontal adjustment is not made properly,
ice size cannot be uniform.
This is because ice was sublimated.
Ice cannot be made until the freezer
compartment is sufficiently cooled.
Ice cannot be made until the freezer
compartment is sufficiently cooled.
R-S42XMJ_(B) (A4).indd 40
R-S42XMJ_(B) (A4).indd 40
3/24/08 4:33:02 PM
3/24/08 4:33:02 PM