English
4
DEMOLITION HAMMER SAFETY WARNINGS
1.
Wear ear protectors.
Exposure to noise can cause hearing loss.
2.
Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
3. Wear protective glasses to protect your eyes.
4. Wear a mask when turning your head upward.
5. Properly set the bit holder.
○
Electric Hammer Oil (one liter)
(Code No.: 955009)
Optional accessories are subject to change without notice.
APPLICATIONS
Crushing concrete, chipping, digging, and squaring.
Application examples:
Installation of piping and wiring, sanitary facility installation,
machinery installation, water supply and drainage work,
interior jobs, harbor facilities and other civil engineering
works.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements speci
fi
ed on the product
nameplate.
2. Grounding
This tool should be grounded while in use to protect the
operator from electric shock. The tool is equipped with a
three conductor cord and grounding type plug to
fi
t the
proper grounding type receptacle. The green (or green
and yellow) conductor in the cord is the grounding wire.
Never connect the green (or green and yellow) wire to a
live terminal.
3. Power switch
Ensure that the power switch is in the OFF position. If the
plug is connected to a receptacle while the power switch
is in the ON position, the power tool will start operating
immediately, which could cause a serious accident.
4. Extension cord
When the work area is removed from the power source,
use an extension cord of su
ffi
cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
5. Feeding oil (refer to the paragraph on oil feeding)
Prior to using the power tool, remove the oil gauge and
do not fail the oil tank with the provided oil. (Although the
oil tank is built in, it contains only a small volume of oil
when shipped from the Hitachi Works.)
6. Mounting a tool
NOTE
When handling bull point, cold chisel and other
accessories, Hitachi standard tools are recommended
for better operation.
6. Since the bit becomes very hot during operation, exercise
extremes very hot.
7. Safe operation depends on one’s stable posture.
8. At the start of work, con
fi
rm the oil supply and screw
tightening.
9. When working at a highly elevated location, pay attention
to articles and persons below.
10. Before starting breaking or chipping a wall,
fl
oor, or
ceiling, thoroughly con
fi
rm that no items such as an
electric cable or conduit are buried inside.
11. Wear protective shoes to protect your feet.
SPECIFICATIONS
Voltage (by areas)*
(110 V, 115 V, 120 V, 127 V, 220 V, 230 V, 240 V)
)
Power Input
1240 W*
Full-load impact rate
1400/min.
Weight (without cord)
15 kg
* Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
(1) Case .............................................................................1
(2) Bull Point (Total Length 410 mm) ..................................1
(3) Oil Feeder .....................................................................1
(4) Wrench .........................................................................1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
○
Cutter (for crushing asphalt)
Total length:
410 mm
Width:
75 mm
Code No.:
944964
○
Cold Chisel
(for grooving and squaring)
Total length:
410 mm
Code No.:
944962
○
Rammer
(for tamping sand and gravel)
Shank
Rammer
Out diameter:
200 mm
Code
No.:
944965
Shank
Total length:
250 mm
Code
No.:
944966
○
Scoop
(for digging ground in various foundation work)
Total length:
380 mm
Code No.:
957154
000Book̲PH-65A̲Asia.indb 4
000Book̲PH-65A̲Asia.indb 4
2014/04/25 16:21:49
2014/04/25 16:21:49