background image

10

C O L

O

HIGH

A C

/

SERVICE

SET TEMP.

"04" indicated.

Select the address of the indoor 

unit to be changed.

C O L

O

HIGH

A C

/

SERVICE

ADDS RN

C O L

O

HIGH

A C

/

SERVICE

ADDS RN

The address and refrigerant cycle 

number of the indoor unit to be set 

change from flashing to remaining lit.

C O L

O

HIGH

A C

/

ADD S RN

SERVICE

Press the "TEMP."    or  

switch to select the address of 

the indoor unit and then press the 

"CHECK" switch.

Press the temperature control   or 

 switch, select "04" for the address 

change mode, and then press the 

"CHECK" switch.

Normal Mode (when unit is not operating)

1. Change to the optional setting mode.

Press the "CHECK" switch and the "RESET" 

switch simultaneously for more than 3 seconds.

"CHECK"

switch

3. Selection of Indoor Unit

2. Selection of Optional Setting Mode

"SERVICE" is

indicated and the

mode number is

flashed.

NOTE:

 * In case of selecting the address not to change, "NO FUNCTION" is 

displayed.

"CHECK" switch

Select the new address to be used after 

changing the address.

The refrigerant cycle number display can be 

changed from 00 to 63 by pressing the "TIME" 

or  switch, and the unit number display can be 

changed from 00 to 63 by pressing the "TEMP."

control  or   switch.

remaining lit when the "CHECK" switch is pressed 

The address display changes from flashing to

after selecting an address.

NOTE:

A refrigerant cycle number of "99" is used in case 

of temporarily avoiding setting an address when 

all indoor unit refrigerant cycle numbers or unit 

numbers are in use.  If an address has been set 

to "99", make sure to subsequently change the 

address to an address within the normal address 

range.

The result of changing the address is displayed several seconds after the "CHECK" switch has been pressed.  "AH" is temporarily 

displayed if address change processing has been completely succeeded, while "EE" is temporarily displayed if the address was unable 

to be changed.  If this happens, repeat the procedure for changing the address.

4. Change the address of the indoor unit.

5. Changing the address of another indoor unit.

Select the address of the indoor unit to be changed.

C O L

O

HIGH

A C

/

SERVICE

ADDS RN

Pressing the "TEMP." control   or   switch after the result of an address change is displayed in step 4 for 

changing the address of an indoor unit, returns to the selection of an indoor unit of step 3.

Repeat steps 3 and 4 until all indoor unit address changes have been completed.

6. Ending Address Change.

"AC" flashes while connections are

being checked.

Press the "RESET" switch 

during selection of an indoor 

unit of step 3, return to the 

normal mode.

C O L

O

HIGH

A C

/

SERVICE

ADDS RN

7. Turning ON Power of Indoor Unit.

Once turn OFF the power of the indoor unit 3 to 5 minutes after 

completing step 6.  After the display on the controller is no  

longer displayed, turn ON the power of the indoor unit.

unit has been successfully 

changed, processing for 

checking connections begins.

Once the address of the indoor

NOTE:

After ending address change in step 6, make sure to turn off the 

power of the indoor unit.  If this procedure is not performed, the 

automatic address function may not be performed properly.

NOTE:

In the case of having changed the address of the indoor unit with 

the controller, make sure to record the new refrigerant cycle

number and unit number of the indoor unit that has been 

changed in the entry column on the printed board.

Entry column

V

V

(3) Address Change Mode 

Change the address (unit number) of the indoor unit.

Содержание PC-AR













Отзывы: