Hitachi DH24PB3 Скачать руководство пользователя страница 6

Страница: 6 / 41

--- 3 ---

4-1. Selling Point Descriptions

4-1-1. Class-top drilling speed

The drilling speed of the Model DH 24PB3 is 1.4 times higher than B and 1.2 times higher than C thanks to the

efficient transmission of the hammering energy.

4-1-2. More comfortable and frisky drilling

The Model DH 24PB3 can drill holes more comfortably and friskily with a light pushing force because the quantity

of body jumping is 20% less than C.

4-1-3. Internal pressure adjustment mechanism

By minimizing variations in the internal pressure during operation, hammering operation is stabilized. In addition,

idling and grease leakage can be prevented.

4-1-4. Non-slip double-layer molded gear cover

The double-layer molded gear cover consists of a plastic resin base covered with a soft resin to ensure ease of

operation and a non-slip grip during chipping (using a round bull point).

4-1-5. Non-slip double-layer molded handle

The double-layer molded handle consists of a plastic resin base covered with a soft resin to ensure a soft-touch

and non-slip grip.

4-1-6. Compact body: Entire length 351 mm

The Model DH 24PB3 has the same helical driving structure as the Model DH 24PB2 to make the entire length as

short as possible to 351 mm. The Model DH 24PB3 has the shortest body in the class.

Maker/Model

HITACHI DH 24PB3

Entire length (mm)

351

360

352

Содержание DH24PB3










































Результаты поиска

Содержание DH24PB3

Отзывы:

Похожие инструкции для DH24PB3

Бренды по названию

Популярные бренды

Hitachi DH24PB3, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание DH24PB3

Отзывы:

Похожие инструкции для DH24PB3

Бренды по названию

Популярные бренды