manualshive.com logo in svg

Hitachi DH24PB3, Технические данные и руководство по обслуживанию

Поделиться
Скачать
Hitachi DH24PB3 Скачать руководство пользователя страница 28

--- 25 ---

Pushing Button 

[17]

Fig. 14

Change Lever 

[20]

(4) Press-fitting the first gear

Press-fit the First Gear 

[52]

 aligning with the shaft end surface of the Second Shaft 

[47]

.  After press-fitting the

First Gear 

[52]

, check that the inside ring of the Reciprocating Bearing 

[51]

 turns smoothly.

(5) Reassembly of the oil seal

Prior to reassembly, apply grease to the inner circumference of the Oil Seal 

[12]

.  However, do not apply

grease to its outer circumference.  Also, when press-fitting the Oil Seal 

[12]

, ensure that it is straight and level.

(6) Reassembly of the internal pressure adjustment mechanism

Push Felt Packing (A) 

[42]

, Valve 

[43]

 and Felt Packing (B) 

[44]

 in the Inner Cover Ass'y 

[39]

 as far as they

will go in this order.

Fig. 15

Inner Cover Ass'y 

[39]

Valve 

[43]

Felt Packing (B) 

[44]

Felt Packing (A) 

[42]

Содержание DH24PB3










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды