manualshive.com logo in svg

Hitachi DH24PB3, Технические данные и руководство по обслуживанию

Поделиться
Скачать
Hitachi DH24PB3 Скачать руководство пользователя страница 20

--- 17 ---

Speed control

The Model DH 24PB3 is equipped with a variable speed control switch which permits free change of the

rotation speed and hammering force.  When drilling in fragile materials, pull the switch trigger gently for low

rotation speed (hammering force) to achieve optimum results.  Note that the switch trigger cannot be pulled to

the full but up to the half in the reverse drilling, and the speed is about half of the forward drilling.  In addition,

the switch stopper cannot be used in the reverse drilling.

8-3.  "Rotation Only" and "Ro Hammering" Changeover Mechanism

The change lever on the Model DH 24PB3 permits quick and easy changeover between the "Rotation Only" and

"Ro Hammering" functions.  When operating the change lever, be sure to continue pressing the pushing

button.  Armature rotation is transmitted to the second shaft and first gear, and then to the clutch via the spline on

the second shaft spline.  Claws on the surface of the clutch engage matching claws on the reciprocating bearing

to convert the rotation into reciprocating motion.  The clutch can travel back and forth on the second shaft.  Claws

on the surface of the clutch is pressed against on the reciprocating bearing by the force of the clutch spring during

usual operation ("Ro Hammering").  The reciprocating bearing is fitted on the second shaft with some play.

When the change lever is set to the "Rotation Only" (    mark) position, the eccentric pin of the change lever forces

the clutch to move against the pressure of the clutch spring in the direction of the front cap, so that it disengages

from the claws on the reciprocating bearing, and the reciprocating bearing stops rotating on the second shaft.

When the change lever is returned to the "Ro Striking" (       mark) position, the force of the clutch spring

presses the clutch back against the reciprocating bearing so that the claws engage to transmit rotation to the

reciprocating bearing once more.

8-4. "Rotation Only" (no hammering)

The Model DH 24PB3 is equipped with a change lever for changeover between "Ro Hammering" and

"Rotation Only" functions, merely mounting the chuck adapter will not stop the hammering action; it is absolutely

necessary to turn the change lever to the "Rotation Only" setting for drilling or driving screws.  Should the change

lever be set to the "Ro Hammering" position when the tool is used for drilling, the hammering action may

cause the drill chuck to be broken or damaged.  Sales personnel should carefully ensure that the buyer is

thoroughly advised on this point.

Содержание DH24PB3










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды