Hitachi DH 24 PF Скачать руководство пользователя

Страница: 6 / 43

--- 3 ---

4-1. Selling Point Descriptions

(1) Three modes changeover mechanism

The Model DH 24PF provides three functions, "rotation and hammering" function, "rotation only" function and a

new "hammering only" function. Thus, the Model DH 24PF is applicable to groove digging and edging with a cold

chisel or a cutter as well as light-duty chiseling with a bull point.

(2) Variable locking mechanism

The Model DH 24PF is equipped with a variable locking mechanism that allows the angle of a tool such as a cold

chisel or a cutter to be rotated conveniently to 36 individual positions in relation to the work in the "hammering

only" function mode.

(3) Class-top drilling speed

The Model DH 24PF has the class-top drilling speed thanks to the efficient transmission of the hammering energy.

(4) Improved resistance to grease leakage

The Model DH 24PF is equipped with a sealed type ball bearing at the tip of the bearing unit while the current

Model DH 24PE (S) is equipped with an open type ball bearing. In addition, the clearance around the bearing is

minimized to improve the resistance to grease leakage.

(5) One-push tool retainer

The tool retainer of the current Model DH 24PE (S) needs sliding the grip to mount the bit. The one-push tool

retainer of the Model DH 24PF eliminates the need for sliding the grip to mount the bit (sliding the grip is required

at removal of the bit).

(6) Non-slip double-layer molded handle

The double-layer molded handle consists of a plastic resin base covered with a soft resin to ensure a soft-touch

and non-slip grip of the handle.

(7) Push-button type forward-reverse changeover switch

The Model DH 24PF is equipped with the push-button type forward-reverse changeover switch that is more

convenient and reliable than the lever-type switch of the current Model DH 24PE (S).

Содержание DH 24 PF












































Результаты поиска

Содержание DH 24 PF

Отзывы:

Похожие инструкции для DH 24 PF

Бренды по названию

Популярные бренды

Hitachi DH 24 PF, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание DH 24 PF

Отзывы:

Похожие инструкции для DH 24 PF

Бренды по названию

Популярные бренды