Hitachi DH 24 PF Скачать руководство пользователя

Страница: 17 / 43

--- 14 ---

8. REFERENCE MATERIAL

8-1. Lubrication

It is not necessary to replenish the grease lubricant unless the tool is disassembled or there is grease leakage

due to a defective seal. Special grease is used in the striking section. Should the striking section (within the gear

cover) be disassembled, carefully remove the old grease from all parts and, on reassembly, inject 50 g (1.8 oz) of

new grease into the gear cover and 10 g (0.4 oz) into the groove portion of inner cover. Be careful not to exceed

the designated amount of grease. Excessive grease will reduce striking efficiency.

Apply Molub Alloy No. 777-1 grease to the pin portion of the change lever.

8-2. Tool Structure

Transmission of rotation

Unlike conventional rotary hammers, the armature shaft in the Model DH 24PF is in parallel with the tool shaft

- the same structure that is employed in most impact drills. This structure was adopted in order to make the

Model DH 24PF more compact for easier handling and operation. Thus, the appearance of the Model

DH 24PF is similar to that of an impact drill. The rotation of the armature is transmitted to the second shaft via

the first gear, and causes it to rotate. The second pinion provided on the second shaft engages the second

gear mounted on the outer circumference of the cylinder. The cylinder is coupled to the second gear by

means of a slip mechanism, and they rotate together. The end of the cylinder also functions as the drill bit

retainer. The cylinder is key-connected to the inserted drill bit by means of two key rails, and transmits rotation

to the drill bit. A steel ball is used to prevent the bit from coming off.

Содержание DH 24 PF












































Результаты поиска

Содержание DH 24 PF

Отзывы:

Похожие инструкции для DH 24 PF

Бренды по названию

Популярные бренды

Hitachi DH 24 PF, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание DH 24 PF

Отзывы:

Похожие инструкции для DH 24 PF

Бренды по названию

Популярные бренды