Hitachi CP-WU8600 Скачать руководство пользователя страница 119

Страница: 119 / 129

119

SHADE

Regarding the indicator lamps

Regarding the indicator lamps (continued)

Indicator Status

Description

There is a possibility that the interior portion

has become heated.

Please turn the power off, and allow the projector to

cool down at least 20 minutes. After the projector has

sufficiently cooled down, please make confirmation of

the following items, and then turn the power on again.

• Is there blockage of the air passage aperture?

• Is the air filter dirty?

• Please use the unit within the temperature range.

NORMAL MODE: 0 to 40°C

ECO MODE: 0 to 45°C

• Is the setting for ALTITUDE appropriate?

• Is the exhaust air (hot/cold) from peripheral

equipments blowing against the ventilation opening

of projector?

For details on ALTITUDE, refer to ALTITUDE of

SERVICE in the OPTION menu. If the projector is

used with a wrong setting, it may cause damage to

the projector itself or the parts inside.

It is time to clean the air filter.

Please turn the power off immediately, and clean or

change the air filter referring to the section

Cleaning

and replacing the air filter

. After cleaning or

changing the air filter, please be sure to reset the

filter timer.

After the remedy, restart the projector.

Other error has occured.

• Please use the unit within the temperature range.

NORMAL MODE: 0 to 40°C

ECO MODE: 0 to 45°C

If the same indication is displayed after the remedy,

please contact your dealer or service company.

(continued on next page)

Red

Red Red

SHADE

Red

Blinking at the

same time

Blinking

alternately

Blinking at the

same time

Содержание CP-WU8600


































































































































Результаты поиска

Содержание CP-WU8600

Отзывы:

Похожие инструкции для CP-WU8600

Бренды по названию

Популярные бренды

Hitachi CP-WU8600, Руководство пользователя

Результаты поиска

Содержание CP-WU8600

Отзывы:

Похожие инструкции для CP-WU8600

Бренды по названию

Популярные бренды