Hitachi CP-C9SM, Руководство по обслуживанию

Страница: 28 / 72

28
CP-S335(C9SM)/CP-X340(C9X)/CP-X345(C9XM)
6-11 Regarding the indicator lamps
Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP indicator have the mean-
ings as described in the table below. Please respond in accordance with the instructions with in the table.
POWER
indicator LAMP
indicator
TEMP
indicator
Description
Lighting
In Orange
Turned
off
Turned
off
The projector is in a standby state.
Blinking
In Green
Turned
off
Turned
off
The projector is warming up.
Please wait.
Lighting
In Green
Turned
off
Turned
off
The projector is in an on state.
Ordinary operations may be performed.
Blinking
In Orange
Turned
off
Turned
off
The projector is cooling down.
Please wait.
Blinking
In Red
(discre-
tionary) (discre-
tionary)
The projector is cooling down. A certain error has been detected.
Please wait until the POWER indicator finishes blink, and then perform the proper
response measure using the item descriptions below as reference.
Blinking
In Red
or
Lighting
In Red
Blinking
In Red
Turned
off
Either there is no lamp cover, or it has not been properly fi xed. Please turn the
power off, and allow the unit to cool down at least 45 minutes.After the projector has
suffi ciently cooled down, please make confi rmation of the attachment state of the lamp
cover, and then turn the power on again.
Blinking
In Red
or
Lighting
In Red
Lighting
In Red
Turned
off
The projector lamp has not been properly fi xed(attached), the lamp does not
light, and there is a possibility that interior portion has become heated.
Please turn the power off, and allow the unit to cool down at least 20 minutes. After
the projector has suffi ciently cooled down, please make confi rmation of the following
items, and then turn the power on again.
• Is there blockage of the air passage aperture?
• Is the air fi lter dirty?
• Does the peripheral temperature exceed 35°C?
If the same indication is displayed after the treatment, please change the lamp by
referring to the section “Lamp”.
Blinking
In Red
or
Lighting
In Red
Turned
off
Blinking
In Red
The cooling fan is not operating.
Please turn the power off, and allow the unit to cool down at least 20 minutes. After
the projector has suffi ciently cooled down, please make confi rmation that no foreign
matter has become caught in the fan, etc. and then turn the power on again.
If the same indication is displayed after the treatment, please change a fan.
Blinking
In Red
or
Lighting
In Red
Turned
off
Lighting
In Red
There is a possibility that the interior portion has become heated.
Please turn the power off, and allow the unit to cool down at least 20 minutes. After
the projector has suffi ciently cooled down, please make confi rmation of the following
items, and then turn the power on again.
• Is there blockage of the air passage aperture?
• Is the air fi lter dirty?
• Does the peripheral temperature exceed 35°C?
If the same indication is displayed after the treatment, please set the HIGH at the
FAN SPEED of the item SERVICE of the OPTION menu.
Lighting
In Green
Alternative
blinking in Red
There is a possibility that the interior portion has become overcooled.
Please use the unit within the usage temperature parameters (5°C to 35°C). After the
treatment, resent the power to ON.
If the same indication is displayed after the treatment, please make sure the wire
connection of the connectors E301 and E302 on the PWB assembly MAIN.
Lighting
In Green
Simultaneous
blinking in Red
It is time to clean the air fi lter.
Filter timer has counted 100hours or more. Please immediately turn the power OFF,
and clean or change the air fi lter by referring to the section “Air Filter”. After cleaning
or changed the air fi lter, please be sure to reset the fi lter timer. After the treatment,
resent the power to ON.
NOTE • When the interior portion has become overheated, for safety purposes, the power source is automati-
cally turned off, and the indicator lamps may also be turned off. In such a case, press the “○” (OFF) side of the
power switch, and wait at least 45 minutes. After the projector has suffi ciently cooled down, please make con-
fi rmation of the attachment state of the lamp and lamp cover, and then turn the power on again.