Hitachi CP-C9SM страница 17 Скачать руководство пользователя

Страница: 17 / 72

CP-S335(C9SM)/CP-X340(C9X)/CP-X345(C9XM)

6. Service points

6-1 Lead free solder [CAUTION]

This product uses lead free solder (unleaded) to help preserve the environment. Please read these

instructions before attempting any soldering work.

Lead free solder indicator

Printed circuit boards using lead free solder are engraved with an "F" or "LF".

Properties of lead free solder

The melting point of lead free solder is 40-50˚C higher than leaded solder.

Servicing solder

Solder with an alloy composition of Sn-3.0Ag-0.5Cu or Sn-0.7Cu is recommended.

Although servicing with leaded solder is possible, there are a few precautions that have to be taken. (Not

taking these precautions may cause the solder to not harden properly, and lead to consequent malfunctions.)

Precautions when using leaded solder

Remove all lead free solder from soldered joints when replacing components.

If leaded solder should be added to existing lead free joints, mix in the leaded solder thoroughly after the

lead free solder has been completely melted (do not apply the soldering iron without solder).

Servicing soldering iron

A soldering iron with a temperature setting capability (temperature control function) is recommended.

The melting point of lead free solder is higher than leaded solder. Use a soldering iron that maintains a high

stable temperature (large heat capacity), and that allows temperature adjustment according to the part being

serviced, to avoid poor servicing performance.

Recommended soldering iron:

Soldering iron with temperature control function (temperature range: 320-450˚C)

Recommended temperature range per part:

Part

Soldering iron temperature

Mounting (chips) on mounted PCB

320˚C±30˚C

Mounting (chips) on empty PCB

380˚C±30˚C

Chassis, metallic shield, etc.

420˚C±30˚C

(1) PWB assembly MAIN

(2) PWB assembly CONTROL

(3) PWB assembly REMC

(4) PWB assembly SW

(5) POWER UNIT (BALLAST)

(6) POWER UNIT (CIRCUIT)

The PWB assembly which has used lead free solder

CAUTION

Always wear safety glasses to prevent fumes or molten solder from getting into the eyes. Lead free solder

can splatter at high temperatures (600˚C).

Содержание CP-C9SM









































































Результаты поиска

Содержание CP-C9SM

Отзывы:

Похожие инструкции для CP-C9SM

Бренды по названию

Популярные бренды

Hitachi CP-C9SM, Руководство по обслуживанию

Результаты поиска

Содержание CP-C9SM

Отзывы:

Похожие инструкции для CP-C9SM

Бренды по названию

Популярные бренды