Hitachi Compute Rack 220H Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 80

background image

6-10

Troubleshooting

Hitachi Compute Rack 210H User’s Guide

Error message

Description

Action

Memory Error. Please check the SDRAM
connection. If problems persist contact Tech
Support.

A cache memory error has occurred in
the disk array controller.

(*1)

Memory Error. Detected Unsupported RAID
Controller Memory.
Contact Tech support.

A cache memory error has occurred in
the disk array controller.

(*1)

Unrecoverable Error. Please check the
SDRAMconnection.
If problems persist contact Tech Support.

A cache memory error has occurred in
the disk array controller.

(*1)

This is a TEST message.
Press any key to ignore it, or wait 5 seconds.
No further action is required.
Press any key to continue, or C to load the
configuration utility.

Test message

(*1)

This firmware is an ALPHA version.
It has not completed all validation.

The firmware is of alpha version.

(*1)

This firmware is a BETA version.
It has not completed all validation.

The firmware is of beta version.

(*1)

This firmware is a TEST version.
It has not completed any validation.

The firmware is of test version.

(*1)

The firmware version inconsistency was
detected. The adapter was recovered, but
cached data was lost.
Press any key to continue or press C to load
the configuration utility.

Firmware version inconsistency has
been detected.

(*1)

Firmware Failed Validation. Adapter needs to
be refreshed.

Firmware version inconsistency has
been detected.

(*1)

The most recent configuration command
could not be committed and must be retried.
Press any key to continue, or press C to load
the configuration utility.

The disk array configuration information
has been cleared or missing.

(*1)

Previous configuration cleared or missing.
Importing configuration created on X/Y
X:Y
Press any key to continue or press C to load
the configuration utility.

The disk array configuration information
has been cleared or missing.

(*1)

An enclosure was found that contains both
SAS and SATA drives, but this controller does
not allow mixed drive types in a single
enclosure.
Correct the problem and restart your system.
Press any key to continue or press C to load
the configuration utility.

The disk array controller is working with
illegal parameters.

(*1)

SAS drives were detected, but this controller
does not support SAS drives.
Remove the SAS drives and restart your
system.
Press any key to continue or press C to load
the configuration utility.

The disk array controller is working with
illegal parameters.

(*1)

«
...
66
67
68
69
70
...
»

Содержание Compute Rack 220H

















































































Отзывы:

Нет отзывов

Похожие инструкции для Compute Rack 220H

Бренд: Friant Страницы: 2

Vigo Hallway Stand

Бренд: Mocka Страницы: 6

Бренд: Mounting Solutions Страницы: 4

Бренд: Tripp Lite Страницы: 3

Бренд: Echogear Страницы: 20

Бренд: Gebesa Страницы: 6

Бренд: peerless-AV Страницы: 20

Бренд: Sennheiser Страницы: 3

Бренд: GRAVITY Страницы: 2

Air Leaf LC0171

Бренд: Innova Страницы: 4

Бренд: CHIEF Страницы: 20

Бренд: VMP Страницы: 4

Бренд: Unicol Страницы: 5

UPPER-LOWER MONITOR

Бренд: Altwork Страницы: 9

Бренд: Konig & Meyer Страницы: 8

Бренд: Kolpin Outdoors Страницы: 7

Бренд: B-Tech Страницы: 16

Бренд: Amada Homefurnishing Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды