Hitachi CD 36DAL, Инструкция по эксплуатации

Страница: 20 / 128

20
English
NOTE
After tightening securely, adjust so that the left side M10
installation nut can be fastened and loosened.
Failure to do so can cause deformation of the fl ange assy
or ba ffl e failure.
(3) Position the rounded side of the left side M10 installation
nut so that it faces the box spanner side and then fasten
securely. ( Fig. 19 )
(4) Check and make sure that the cutting blade has been
properly installed. ( Fig. 20 )
6. Installing the shoulder belt
Use in combination with a BSL3620 battery.
WARNING
◯
Be sure to attach the shoulder belt so that the grass
trimmer can be carried correctly.
◯
If you get the feeling the tool is not operating normally,
turn o ff the motor immediately, remove the quick-release
bracket of the shoulder belt and remove the tool.
CAUTION
◯
If you do not support the tool when you pull the quick-
release belt, it may fall causing injury or damage.
Hold the main pipe with one hand while you pull with the
other hand.
◯
Make sure the quick-release function operates normally
before you start working.
(1) Place the shoulder belt on the shoulder as shown in Fig.
11 (For use outside of Europe, see Fig. 13 ) and engage
it with the hanger on the tool. Adjust the shoulder belt to
suitable length.
(2) To remove the tool from the shoulder belt, support the
tool by holding the main pipe with one hand and use the
other hand to pull the quick-release belt as shown in Fig.
11 (For use outside of Europe, see Fig. 13 ) to free it from
the bracket.
(3) To strap on the tool, insert the bracket in the hook and
insert the quick-release bracket over the hook and into
the wide opening of the bracket. ( Fig. 12 ) (For use
outside of Europe, see Fig. 14 )
Gently pull the shoulder belt to make sure that it is
properly attached.
7. Installing the hanger belt
Use in combination with a BL36200 battery.
WARNING
◯
Be sure to attach the hanger belt so that the grass
trimmer can be carried correctly.
◯
If you get the feeling the tool is not operating normally,
turn o ff the motor immediately, press the release
mechanism of the hanger belt and remove the tool.
CAUTION
◯
If you do not support the tool when you press the release
mechanism, it may fall causing injury or damage.
Hold the main pipe with one hand while you push with
the other hand.
◯
Make sure the release function operates normally
before you start working.
(1) Hook the hanger belt to the BL36200 harness (two
places) as shown in Fig. 15 . Then hook the belt to the
hanger of the main pipe (one place). Adjust the hanger
belt to a suitable length.
(2) To detach the tool from the hanger belt, hold the main
pipe with one hand and press the release mechanism of
the hanger belt from both sides as shown in Fig. 16 .
To attach the tool, insert from below, making sure that is
it properly attached.
NYLON HEAD
Installation of semi-auto nylon head
1. Function
Automatically feeds more nylon cutting line when it is
tapped.
Speci fi cations
Code No.
Type of
attaching
screw
Direction of rotation
Size of
attaching
screw
335234
Female
screw
Counterclockwise
M10×
P1.25-LH
Applicable nylon cord
Cord diameter: Fig. 21
Length: 4 m
CAUTION
◯
The case must be securely attached to the cover.
◯
Check the cover, case and other components for cracks
or other damage.
◯
Check the case and button for wear.
If the wear limit mark on the case is no longer visible or
there is a hole in the bottom of the button, change the
new parts immediately. ( Fig. 24 )
◯
The nylon head must be securely mounted to the
threaded fastener of the motor case.
◯
For outstanding performance and reliability, always
use Hitachi nylon cutting line. Never use wire or other
materials that could become a dangerous projectile.
◯
If the nylon head does not feed cutting line properly,
check that the nylon line and all components are properly
installed. Contact your Hitachi dealer if you need
assistance.
2. Installation (Fig. 17 and 22)
(1) Insert the fl ange assy into the motor case. At this time,
the wing of the fl ange assy should face the motor case
side. Next, align the holes of the fl ange assy and the
motor case, insert the hex. bar wrench 4 mm, and then
turn to tighten the fl ange assy.
(2) Screw the nylon head directly to the threaded fastener of
the motor case.
The mounting nut of nylon head is left-hand-threaded.
Turn clockwise to loosen/ counterclockwise to tighten.
CAUTION
Install the nylon head properly and securely as instructed
in the handling instructions.
If not attached properly or securely, it may come o ff and
cause injury.
3. Adjustment of line length
Rotate and tap the nylon head on the ground. Nylon line
is drawn out abt, 30 mm by one tapping. ( Fig. 23 )
Also, you can extend nylon line with hands. This time the
motor must be completely stopped.
Con fi rm the line extends in 30 mm increments by
“tapping” and “releasing” the bottom button while pulling
the line ends of the nylon head. ( Fig. 24 )
◯
Appropriate Length of Nylon Line
The appropriate length of the line when the tool is in use
is 90 – 110 mm. Extend the line to the appropriate length.
4. Nylon line replacement
(1) Prepare 4m of genuine nylon line in Fig. 21 . (Code No.
335235)
(2) Press the opposing tabs, and then remove the cover
from the case. ( Fig. 25 )
(3) Remove the reel from the case. ( Fig. 26 )
◯
If there is nylon line remaining, hook the line in the groves,
and then remove the reel.
000Book̲CG36DL̲WE.indb 20 000Book̲CG36DL̲WE.indb 20 2013/08/27 17:09:57 2013/08/27 17:09:57