Hitachi C10LA - 10" Cabinet Saw, Инструкция по эксплуатации

Страница: 6 / 76

– 6 –
English
DO NOT MODIFY THE PLUG PROVIDED. If it will not
fi t the receptacle, have the proper receptacle installed
by a qualifi ed electrician.
IMPROPER CONNECTION of the equipment grounding
conductor can result in risk of electric shock. The
conductor (wire) with the green insulation (with or
without yellow stripes) is the equipment grounding
conductor. If repair or replacement of the electric cord
or plug is necessary, DO NOT connect the equipment
grounding conductor to a live terminal.
CHECK with a qualifi ed electrician or service personnel
if you do not completely understand the grounding
instructions, or if you are not sure the saw is properly
grounded.
Use only 3-wire extension cords that have 3-prong
grounding plugs and 3-pole grounding receptacles that
accept the saw’s plug. Repair or replace damaged or
worn cords immediately.
240V OPERATION
The table saw provided a dual voltage, 120V and 240V,
motor. To operate the table saw at 240V, single phase,
reconnect the motor wire as the wire wirding on page
74.
To avoid injury, disconnect the motor from power source
outlet before reconnecting the wire.
To operate the table saw at 240V, replace the 120V
plug with a UL/CSA listed plug suitable for 240V (not
included) and the rated current of the saw as shown.
Contact your local Hitachi Authorized Service Center or
qualifi ed electrician for proper procedures to install the
plug. The saw must comply with all local and national
electrical codes after the 240V plug is installed. Connect
the table saw with 240V plug to a power source outlet
as shown.
ELECTRICAL REQUIREMENTS AND SAFETY
POWER SUPPLY REQUIREMENTS
To avoid electrical hazards, fi re hazards or damage
to the table saw, use proper circuit protection.
Always use a separate electrical circuit for your
tools. This power tool is wired at the factory for
120V operation. Connect it to a 120V, 15 Amp circuit
and use a 15 Amp time delay fuse or circuit breaker.
To avoid shock or fi re, replace the cord immediately
if it is worn, cut or damaged in any way.
EXTENSION CORD REQUIREMENTS
Any extension cord must be GROUNDED for safe
operation.
GUIDELINES FOR EXTENSION CORDS
Any extension cord used for power tools MUST be
grounded (3-wire with two fl at prongs and one round
ground prong).
Make sure the extension cord is in good condition.
When using an extension cord, make sure you use one
heavy enough to carry the current the tool will draw.
An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. The table
above shows the correct size to use according to
extension cord length and nameplate ampere rating. If
in doubt, use the next heavier gauge cord. The smaller
the gauge number the heavier the cord.
NOTE:
The 12 to 16 amp rating is correct for this tool. It
is highlighted in the table above.
Be sure your extension cord is properly wired and in
good condition. Always replace a damaged extension
cord or have it repaired by a qualifi ed person before
using it. Protect your extension cords from sharp
objects, excessive heat and damp or wet areas.
Before connecting the saw to the extension cord, make
sure the saw switch is turned OFF.
GROUNDING INSTRUCTIONS
IN THE EVENT OF A MALFUNCTION OR
BREAKDOWN, grounding provides a path of least
resistance for electric current and reduces the risk of
electric shock. This saw is equipped with an electric
cord that has an equipment grounding conductor and
a grounding plug. The plug MUST be plugged into
a matching receptacle that is properly installed and
grounded in accordance with ALL local codes and
ordinances.
WARNING
WARNING
MINIMUM GAUGE FOR EXTENSION CORDS (AWG)
Ampere Rating Volts Total length of Cord
More Than Not More Than
120V
240V 25ft. 50ft. 100ft. 150ft.
50ft. 100ft. 200ft. 300ft.
0 6 18 16 16 14
6 10 18 16 14 12
10 12 16 16 14 12
12 16 14 12
Not Recommended
-Prong Plug
Grounding Prong
Properly Grounded
3-Prong Receptacle
Make sure this is
connected to a
known ground.
-Prong
Receptacle
WARNING