10
How to Install the Water Supply Hose
供水管的安裝
Firmly tighten the union nut
when connecting the water
supply hose to the water inlet.
沿箭頭方向旋轉連接
絲
母,使其
與供水口緊緊相連。
Please use optional extension pipe
to extend length of the water supply
hose.
請使用另行銷售的延長供水管。
Union nut
Ⳑ
䴚
ᕒ
Connecting the water supply hose to the washer
供水管與機體的連接
Extending the water supply hose
供水管的延長
• Loosely tightened union nut will cause water leakage.
請務必擰緊供水管與機體的連接
絲
母。否則,將會漏水。
• When removing the hose, unscrew the union nut fi rst.
拆卸供水管時,先鬆開連接
絲
母,再進行拆卸。
• Three standard extension hoses (1m,2m,3m)
are available. Please inquire distributors for
extending the water supply hose.
備有
1m
、
2m
和
3m
三種規格供購買。如欲延長供
水管,請向銷售商查詢。
Water leakage
may occur.
ሷר⋱ሳភᖛȯ
Distance must be over 1.6cm
in order to install correctly.
ᤀ
1.6cm
˫ʀ᱿⭡サ૽ᤀ
ᘍમ⡶ȯ
May break off after installing
the one touch joint.
͵࿌Ⳑݽમ⡶രŊ
ר⋱ሳ⌉┛ȯ
How to Install the One Touch Joint
便捷連接器的安裝
1
Confi rm the diameter of the water tap.
確認水龍頭直徑。
• For water supply hose installation, please refer to "How to install the water supply hose" in the user manual.
供水管的安裝參閱使用說明書中「供水管的安裝」一章。
• Loosening may occur after a long time use. In such a case, reinstall the joint following steps 2 to 4.
長時間使用後,可能會因鬆脫而引起漏水,此時請按
2~4
的步驟重新安裝。
(Follow the same steps when reinstalling the one touch joint when you move the machine to another location.)
(搬家等需重新安裝便捷連接器時,請按照相同的步驟進行。)
Horizontal tap A
橫式
A
型水龍頭
Horizontal tapB
橫式
B
型水龍頭
Square mouth tap
方口水龍頭
Universal household tap
萬能水龍頭
Swivel tap
萬向水龍頭
2
3
4
Tighten joint
B
in
the arrow direction
to reduce the gap
between joint
A
and
B
to 4mm or less.
沿箭頭方向擰緊接頭
B
,使接頭
A
、
B
之間的間隙在
4mm
以內。
Screw
➦⸎
Label
ᐻ⫅
One touch joint
͵࿌Ⳑݽ
Joint ring
Ⳑ᭔
Check the distance between
joints
A
and
A
.
確認接頭
A
、
B
之間的間隙。
ㆊ
Approximately 6mm
₎
6mm
ㆊ
A
Joint
A
Joint
B
B
Press the sealed
pad evenly
against the
tap and tighten
the four screws
uniformly.
將密封墊均勻地壓
在水龍頭上,再將
4
個螺釘均等地擰
緊。
Water tap
ᖛ㕻ㆊ
Sealed pad
ૺࣆ
Joint
ㆊ
B
B
Tighten screw in advance if
it is located close to the wall.
ㄅⲖᦷࣦ᱿➦⸎Ŋרㅷ҅ᮢ
༆ეⳖɺˀȯ
Less than 4mm
₎
4mm
˫ʁ
ㆊ
ㆊ
(After tighten)
(
ეℤര
)
B
Joint
B
A
Joint
A
Appropriate water tap
適用的水龍頭
Horizontal taps A and B as shown below.
橫式
A
、
B
型水龍頭最為適宜。
• If the diameter exceeds
2cm, remove the joint
ring.
若水龍頭的外經超過
2cm
,可將連接環取出。
• Screw joint
B
in the
arrow direction to adjust
the gap.
沿箭頭方向旋轉接頭
B
調
整間隙。
Installation Guide (continued)
安裝指南(續)