Hitachi 50PD9800TA, Руководство по обслуживанию

Страница: 20 / 88

20
50PD9800TA (FW1)
n o it c n u F .j d A
No. A e d o M s m e tI . J D
Init.
Value
Max.
Value
Device
535 Reserved - - -
536 Reserved - - -
537 Reserved - - -
538 Reserved - - -
539 Reserved - - -
540 Reserved - - -
541 Reserved - - -
542 Reserved - - -
543 Reserved - - -
544 Reserved - - -
545 Reserved - - -
546 Reserved - - -
547 Reserved - - -
548 Reserved - - -
549 Reserved - - -
550 Reserved - - -
551 Reserved - - -
552 Reserved - - -
553 Reserved - - -
554 RF-PAL IF compensation Enable 0:Disable, 1:Enabl 1 0 Subsys
555 DTT Force Reset 5:Yes(Reset), 0
㨪 4,6,7:No(Normal),
7 0 -
556 Sub system Busy Check 0:Disable, 1:Enabl 1 1 -
557 Sub system Blanking (for DEBUG 0:Normal, 1:Main, 2:Sub, 3:Both 3 0 Subsys
558 HDMI Output clock invert 0:Normal(Rising edge), 1:Invert(Falling edge 1 0 HDMI
559 HDMI OUTPUT FORMAT (0:RGB4:4:4, 1/2:YCbCr4:4:4 * YCbCr4:2:2 unused (9/1 2 2 HDMI
560 Sub system status [00h]: Signal, Panel frame rate, Color syste - - -
561 Sub system status [01h]: Input signal mod - - -
562 Sub system status [02h]: H.Freq.(H - - -
563 Sub system status [03h]: H.Freq.(L - - -
564 Sub system status [04h]: V.Freq.(H - - -
565 Sub system status [05h]: V.Freq.(L - - -
566 Sub system status [06h]: V.Total(H - - -
567 Sub system status [07h]: V.Total(L - - -
568 Sub system status [08h]: (OSD mode - - -
569 Sub system status [09h]: (Factory menu - - -
570 Sub system status [0Ah]: Teletext status(H - - -
571 Sub system status [0Bh]: Teletext status(L - - -
572 Sub system status [0Ch]: WSS info. - - -
573 Sub system status [0Dh]: CNI code(H - - -
574 Sub system status [0Eh]: CNI code(L - - -
575 Sub system status [0Fh]: NI code(H - - -
576 Sub system status [10h]: NI code(L - - -
577 Sub system status [11h]: Version(H - - -
578 Sub system status [12h]: Version(L - - -
579 Sub system "Status-read" request available (0:No 1:Yes 1 1 -
580 Sub system "OSD-packet" refresh available (0:No 1:Yes 1 0 -
581 Sub system "Control-packet" refresh available (0:No 1:Yes 1 0 -
582 Inp.Mode (0-2:AUTO, 3-10:576i/480i/576p/480p/720p60/1080i50/60/720p50) 10 0 -
583 Sub system H.B. stop coun 254 0 -
584 Force Sub Video Decoder ON mod 1 0 -
585 No signal Power-ON DEBUG mod 1 0 -
586 Panel Blanking Enable (when the input signal is changed 1 0 -
587 Input H.Freq.(Subsys-02&03h / 10) * cutoff below decimal point (31.5kHz -> "31") - - -
588 Input V.Freq.(Subsys-04&05h / 10) * cutoff below decimal point (59.9Hz -> "59") - - -
589 IIC BUS Data/Clock Open(0:Close, 1:Open 1 0 M30627
590 HDMI EDID WRITE ENABLE 1 0 M30627
591 F F O : 0 , N O : 1 F F O / N O K L B - P D P 1 0 PDP
592 RS232C Terminal control mode 0:Terminal, 1:Genesis, 2:DTT(Write
Reserved for Australia DTT
2 1 M30627
593 Reset function of accumulation time for LCD Panel 0:Normal 1:Reset 1 0 M30627
594 Accumulation time for Panel (hours 65535 - PDP
595 Display of Panel map versio 255 - PDP
596 W/B Initialize 1 - M30627
597 Gain adjustment (Calibration) 1 - -
598 EEPROM Initialize(0:No, 1:Yes 1 0 M30627
599 Enter to adjust menu(2 - - M30627
600 Enter to service menu of Sub-syste - - FLI8538
e
e
)
)
)
m
e
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
t
e
e
)
)
)
)
n
)
)
m