Hisense LHD32K21MH, Руководство пользователя

Страница: 5 / 21

Installing and removing the stand
3
Caut i ons
Damage requiring service
U np l ug this TV from the po w er out l
ser v ice personne l under the fo ll o w ing conditions :
When the po w er supp l y cord or p l ug is damaged or frayed .
I f l i q uid has been spi ll ed or objects ha v e fa ll en into your TV.
I f your TV has been exposed to rain or w ater .
I f your TV does not operate norma ll y by fo ll o w ing the operating
instructions . Adjust on l y those contro l s that are co v ered by the
operating instructions because incorrect adjustment of other
contro l s may resu l t in damage and w i ll often re q uire extensi v e
nician to restore your TV to its norma l
operation .
I f your TV has been dropped or damaged in any w ay .
When your TV exhibits a distinct change in performance .
Outdoor antenna grounding
I f an outside antenna or cab l e system is connected to your TV, make sure
that the antenna or cab l e system is grounded to pro v ide some
protection against v o l tage surges and bui l t - up static charges . Artic l e
8 1 0 of the N ationa l El ectrica l Code , A N S I/NFP A N o . 7 0 , pro v ides
information w ith respect to correct grounding of the mast and
supporting structure , grounding of the l ead - in w ire to an antenna
discharge unit , si z e of grounding conductors , l ocation of the
antenna - discharge unit , connection to grounding e l ectrodes , and
re q uirements for the grounding e l ectrode .
Note to CATV system installer
Artic l e 820 of the N ationa l El ectrica l Code , A N S I/NFP A N o . 4 0 pro v ides
it states that the cab l e
ground must be connected to the grounding system of the bui l ding as
c l ose to the point of cab l e entry as practica l.
Condensation
Moisture w i ll form on the TV if the TV is brought from coo l surroundings
into a w arm room or if the temperature of the room rises sudden l y .
When this happens , the TV' s performance may be impaired . T o pre v ent
this , l et the TV stand in its ne w surroundings for about an hour before
s w itching it on , or make sure that the room temperature rises gradua ll y .
Condensation may a l so form during the summer if the TV is exposed to
the bree z e from an air conditioner . I n such cases , change the l ocation of
the TV.
Mobile telephone warning
T o a v oid interference w ith your TV picture and sound , operating
prob l ems , or e v en damage , keep your cord l ess and ce ll u l ar te l ephones
a w ay from the TV.
End of l i fe d i rect i ves
sma ll amount of mercury . Disposa l of these materia l s may be regu l ated
for en v ironmenta l reasons . Y our TV a l so contains materia l that can be
recyc l ed and reused . F or disposa l or recyc l ing information , contact your
l oca l authorities or the El ectronic I ndustries A ll iance at www. eia . org to
Non-act i ve p i xels
pro v ide exceptiona ll y sharp v ideo q ua l ity . Occasiona ll y , a fe w
of your TV, and are not considered defects .
Accessor i es
Make sure the fo ll o w ing accessories are inc l uded in the box w ith your
TV:
Remote contro l
AC po w er cord
AAA batteries ( 2 )
Stand
Quick Setup Guide
Install i ng and remov i ng the
stand
Y ou must insta ll your TV into the stand in order for it to stand upright on
or other v ertica l surface , you must remo v e the stand .
Warning
: Before attampting assembly or removal of the stand, unplug
the AC power cord.
Cautions
:
Read these instructions carefully before you try to assemble the stand
or remove the stand .
Make sure that you handle the TV carefully when attempting to
assemble or remove the stand. If you are not sure of your ability to do
this, contact a professional installer or service technician. Hisense is
not responsible for any damages or injuries that occur because of
mishandling or incorrect assembly.
Use a soft cushion or covering to prevent scratching or damage to the
TV screen or cabinet.
Install i ng the stand
Note
To install the stand:
1.
Antenna lead-in wire
Grounding clamp
Antenna discharge unit
Grounding conductors
Ground clamps
Power service grounding electrode
system
Electric service equipment
2
1
3
4
5
6
7
1
2
3
4
5
6
7
LHD32K21MH
I nsert the stand co l umn into the base p l ate , a l igning the ridge
on the co l umn w ith the groo v e in the base p l ate .
Making sure the F RO NT of stand co l umn match the F RO NT of
base p l ate .
Secure the stand co l umn to the base p l ate w ith the four scre w s
( M 4, 1 2mm ) pro v ided .
E