manualshive.com logo in svg

Hirschmann BAT-R, Руководство пользователя

Поделиться
Скачать
Hirschmann BAT-R Скачать руководство пользователя страница 15

Installation BAT-R

Release 09 03/2017

15

Notes:

Applies to the operation of devices in the 5.6 to 5.65 GHz band:
Install an antenna with an antenna gain of at least 3 dBi.

Applies to the operation of devices with antennas having a gain of 
more than 8 dBi:
At temperatures lower than 

−

25 °C a power reduction of 4 dB using a 

software setting has to be applied. This reduction applies in addition to 
the antenna gain setting.

Applies to the operation of antennas having a gain of more than 
18 dBi:
For the operation of 5 GHz indoor channels (channels 36 to 64) a 
power reduction of 4 dB using a software setting has to be applied. 
This reduction applies in addition to the antenna gain setting.

Applies to the operation of the BAT-ANT-N-14G-IP23 antenna:
In addition to the antenna cable supplied, the use of the BAT-CLB-2 N 
m-f antenna is required.

See “Accessories” on page 65.

 
The frequency band 5725 MHz to 5875 MHz is subject to special 
operation conditions. In Germany the usage of this band is restricted to 
commercial public telecommunication services  (BFWA - Broadband 
Fixed Wireless Access). Registration at the Federal Network Agency is 
required. In other European countries the terms of use of the local 
frequency regulation authorities need to be followed.

LED or laser components

LED or LASER components according to IEC 60825-1 (2014):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT

FCC note:

This device complies with part 15 of the FCC rules. 
Operation is subject to the following two conditions: 

This device may not cause harmful interference, and

This device must accept any interference received, including 
interference that may cause undesired operation.

 
This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses 
and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio 

Содержание BAT-R







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды