background image

 

2

 

2. General Safety Instructions

 

 
 

 

ELECTRIC SHOCK 

NEVER touch the output terminals 

during operation

 

NEVER touch the output terminal during 

operation even though the breaker on the 

load is being set at “OFF” position.

   

 

ALWAYS stop engine and make sure it 

stopped before you will connect the loads to 

the output terminals.

   

 

Suffocation  by  exhaust gas

 

 

NEVER run the engine indoors! Make 

sure there is always good ventilation. 

Fumes from engine exhaust cause 

serious injury.

 

 

ALWAYS operate the equipment in the 

ventilated area. 

When the equipment is used in a tunnel, hall 

or any other indoor, the equipment for 

ventilation must be used to prevent serious 

accident caused by suffocation.   

 

NEVER direct the exhaust fume to 

houses nearby while considering the wind 

flow direction.   

Exhaust gas contains many harmful 

elements that would cause affect to human. 

Be free from suffocation when the 

equipment is used in poorly ventilated area 

such as inside of the building. 

 
 

 
 

 

Entangled Injuries under 

By      Moving Componen

 

NEVER reach and touch the moving 

component during operation!

 

 

ALWAYS stop the engine during inspection 

to prevent serious bodily injury by entangled 

accident under moving component.

 

  Electric shock/Injuries/Burns 

 

 

Never inspect equipment during 

use

.

 

Never serve and inspect when equipment is 

being operated. 

It may cause electric shock, injuries or 

burns.

 

 

 

WARNING-Use good judgment

 

  NEVER run the engine when 

transporting the equipment. 

 

ALWAYS stop the equipment 

immediately if it suddenly begins to 

violate or abnormal noise. Inspect for 

broken, missing or improperly installed 

parts.

 

 

ALWAYS keep the equipment as clean 

as practical. Keep it free of loose 

vegetation, mud, etc.

 

 

DO NOT make unauthorized 

modifications or alterations to this equipment 

of any of its components. YAMABIKO must 

authorize alterations and modifications in 

writing. Unauthorized modifications or 

alterations may alter the equipment 

operation and could jeopardize personal 

safety during operation.

 

WARNING

 

 

   

Содержание HW400A









































Отзывы: