manualshive.com logo in svg

HiP 25D815, Инструкция-перечень запасных частей

Поделиться
Скачать
HiP 25D815 Скачать руководство пользователя страница 26

Troubleshooting 

26

3A6828B

Troubleshooting

1. Follow 

Pressure Relief Procedure

, page 11, 

before checking or repairing pump.

2. Turn the disconnect switch (8) to the OFF position. 

3. Disconnect the PT2020 from the AC outlet.

4. Check all possible problems and causes before dis-

assembling pump.

5. Reconnect the PT2020 to the AC outlet after trou-

bleshooting.

6. Turn the disconnect switch (8) to the ON position.

Alarm

Trigger Condition

Return to Standby Condition

Solution

I/O Fault

Whenever the PLC cannot 
communicate with the I/O 
cards. The I/O cards control 
the communication to the sen-
sors and items being con-
trolled.

Once all I/O is detected and 
user acknowledges the alarm.

Check the Ethernet cable that 
connects the PLC to the I/O 
cards and reseat the connec-
tions, if necessary.
Contact Graco Tech Assis-
tance.

No Transducer

Whenever the 4-20 mA signal 
is not in range.

Once the alarm is acknowl-
edged and the transducer is 
detected.

Verify the transducer is prop-
erly connected by reseating 
the cable connections.
Contact Graco Tech Assis-
tance.

Pressure Test 
Failed

Interaction failed by user, or 
pressure decay failed.

Once alarm is acknowledged 
and pressure is relieved.

Determine what caused the 
test to fail and rerun the test.

Over Pressure

Pressure went above the max-
imum test pr the over 
pressure allowed threshold.

Once the alarm is acknowl-
edged and pressure is 
relieved.

Check for leaks in the system.
Lower the gain setting.
Increase the over pressure 
threshold if safe to do so.

Test Unsafe

A test to be run would result in 
the pressure transducer being 
over pressured.

Once the alarm is acknowl-
edged.

Pick a different pressure test 
to run.
Verify the transducer matches 
the transducer selected on the 
Transducer screen.
Use a transducer that is prop-
erly sized for the pressure test.

Unable to Build 
Pressure

The Pressure Test Timeout 
timer expires before the set-
point pressure is reached.

Once the alarm is acknowl-
edged and pressure is 
relieved.

Check for any reason the sys-
tem is not building pressure.
Increase the time on the Pres-
sure Test Timeout timer.
Increase air supply pressure.

Содержание 25D815



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды