HIOS CLT-AY-61 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 14

background image

4

●

Rear Panel (Terminal location of CLY-AY-81 is different from CLT-AY-61 but same function)

Terminal

：

Connect Input and/or Output cables.

Terminal is removable by unscrewing 2 screws at the both end of the terminal.

When you do it, unscrew each of screw little by little.

The table below is the status of switches of the PCB set at HIOS factory.

If you change the setting, refer to the section of “Input/Output setting”

Fuse Holder : 1 each of Fuse and Spare Fuse are installed.

If the Fuse is cut then the lamp of AC Switch and LED lamps do not lit,

replace with Spare Fuse.

«
...
3
4
5
6
7
...
»

Содержание CLT-AY-61















Отзывы:

Нет отзывов

Похожие инструкции для CLT-AY-61

Бренд: Nautel Страницы: 70

Бренд: Nautel Страницы: 72

Бренд: Nautel Страницы: 166

Бренд: TalkingSign Страницы: 12

Бренд: M-system Страницы: 4

Бренд: M-system Страницы: 7

Бренд: Jamara Страницы: 8

Бренд: R.V.R. Elettronica Страницы: 12

Бренд: Icom Страницы: 56

Бренд: AAS Страницы: 8

Wireless Room Temperature Transmitter

Бренд: BAPI Страницы: 2

Бренд: Linear Страницы: 2

Бренд: MKS Страницы: 55

THERMOPOINT TM/J-500

Бренд: NIVELCO Страницы: 28

Бренд: SVP Страницы: 165

Бренд: Sencore Страницы: 3

Бренд: AUDIOropa Страницы: 88

Бренд: Climax Technology Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды