background image

11

Range

9660, 9695-03

9661

500.00A

-

±2.3% rdg. ±0.31% f.s.

100.00A

±2.3% rdg. ±0.32% f.s.

±2.3% rdg. ±0.35% f.s.

50.000A

±2.3% rdg. ±0.34% f.s.

±2.3% rdg. ±0.4% f.s.

10.000A

±2.3% rdg. ±0.5% f.s.

±2.3% rdg. ±0.8% f.s.

5.0000A

±2.3% rdg. ±0.7% f.s.

±2.3% rdg. ±1.3% f.s.

Range

9669

1.0000kA

±3% rdg. ±0.31% f.s.

200.00A

±3% rdg. ±0.35% f.s.

100.00A

±3% rdg. ±0.4% f.s.

Range

9694

9695-02

50.000A

-

±2.3% rdg. ±0.32% f.s.

10.000A

-

±2.3% rdg. ±0.4% f.s.

5.0000A

±2.3% rdg. ±0.32% f.s.

±2.3% rdg. ±0.5% f.s.

1.0000A

±2.3% rdg. ±0.4% f.s.

±2.3% rdg. ±1.3% f.s.

500.00mA

±2.3% rdg. ±0.5% f.s.

±2.3% rdg. ±2.3% f.s.

Range

CT9667-01, -02, -03  5.000kA 

range

CT9667-01, -02, -03  500A 

range

5.0000kA

±4% rdg. ±0.6% f.s.

-

1.0000kA

±4% rdg. ±1.8% f.s.

-

500.00A

±4% rdg. ±3.3% f.s.

±4% rdg. ±0.6% f.s.

100.00A

-

±4% rdg. ±1.8% f.s.

50.000A

-

±4% rdg. ±3.3% f.s.

CLAMP ON SENSOR 9660 / 9695-03 / 9661

*2

Voltage Connection

Current

9661only

5.0000A

10.000A

50.000A

100.00A

500.00A

400.0V

1P2W

2.0000kW 4.0000kW 20.000kW 40.000kW 200.00kW

1P3W

1P3W1U

3P3W2M

3P3W3M

4.0000kW 8.0000kW 40.000kW 80.000kW 400.00kW

3P4W

6.0000kW 12.000kW 60.000kW 120.00kW 600.00kW

CLAMP ON SENSOR

 9669

Voltage Connection

Current

100.00A

200.00A

1.0000kA

400.0V

1P2W

40.000kW

80.000kW

400.00kW

1P3W

1P3W1U

3P3W2M

3P3W3M

80.000kW

160.00kW

800.00kW

3P4W

120.00kW

240.00kW

1.2000MW

CLAMP ON SENSOR 9694 / 9695-02 

*1

Voltage Connection

Current

500.00mA 1.0000A

5.0000A

10.000A

50.000A

400.0V

1P2W

200.00W

400.00W 2.0000kW 4.0000kW 20.000kW

1P3W

1P3W1U

3P3W2M

3P3W3M

400.00W

800.00W 4.0000kW 8.0000kW 40.000kW

3P4W

600.00W 1.2000kW 6.0000kW 12.000kW 60.000kW

*1

 For the 9694 sensor, the range of guaranteed accuracy is from 500 mA to 5 A, 

   and for the 9695-02, from 500 mA to 50 A.

*2

 For the 9660 and 9695-03 sensors, the range of guaranteed accuracy is from 5 A to 100 A

    and for the 9661, from 5 A to 500 A.

Leak current: CLAMP ON LEAK SENSOR 9657-10, 9675

Range 50.000mA / 100.00mA / 500.00mA / 1.0000A / 5.0000A

Apparent power

±1 dgt. for the calculation obtained from each measurement value

Reactive power

Fundamental waveform calculations

±2.0% rdg. ±3.0% f.s. + clamp-on sensor accuracy (w/power factor = 1)

Rms calculations

From each measurement applied to calculation ±1 dgt.

Energy

Active and reactive power measurement accuracies ±1 dgt.

Power factor

From each measurement applied to calculation ±1 dgt.

Frequency

±0.5% rdg. (with 90 to 520 V sine wave input)

Demand value

Active and reactive power measurement accuracies ±1 dgt.

Demand quantity

Active and reactive power measurement accuracies ±1 dgt.

Conditions of 

guaranteed accuracy

After 30 minute warm-up, with 50/60 Hz sine wave input

voltage to earth 400V  or less

Temperature and humidity

for guaranteed accuracy

23˚C ±5˚C (73 ± 9°F), 80%RH or less

(applies to all specifications unless otherwise noted)

Display area 

of guaranteed accuracy Effective measurement range

Period of guaranteed acuracy Accuracy guaranteed for 1 year

Post-adjustment accuracy guaranteed for 6 months

Real-time clock accuracy Within ±0.3 sec/day (with power on, within specified 

operating temperature and humidity ranges)

Temperature characteristic Within ±0.1% f.s./ ˚C (except 23 ±5°C)
Effect of external 

magnetic field

Within ±1.5% f.s. 

(in a magnetic field of 400 A/m rms AC, 50/60 Hz)

Effect of radiated, 

radio-frequency, 

electromagnetic field

Within ±5% f.s. 

for voltage and active power at 10 V/m

Range

Total display range

Effective measurement range

Total display range

Effective peak

Minimum

Minimum

Maximum

Maximum

Range

Voltage

400V Range

5.0V

90.0V

520.0V

520.0V

±750Vpeak

Current

5A Range

0.0200A

0.2500A

5.5000A

6.5000A

±20Apeak

10A Range

0.040A

0.500A

11.000A

13.000A

±40Apeak

50A Range

0.200A

2.500A

55.000A

65.000A

±200Apeak

100A Range

0.40A

5.00A

110.00A

130.00A

±400Apeak

500A Range

2.00A

25.00A

550.00A

650.00A

±1000Apeak

Measurement Range Configurations

Current Display and Effective Measurement Ranges

typical

Combined Accuracy

PW3365-20 +  clamp sensors

AC FLEXIBLE CURRENT SENSOR CT9667-01, -02, -03 (500A)

Voltage Connection

Current

50.00A

100.00A

500.00A

400.0V

1P2W

20.000kW

40.000kW

200.00kW

1P3W

1P3W1U

3P3W2M

3P3W3M

40.000kW

80.000kW

400.00kW

3P4W

60.000kW

120.00kW

600.00kW

AC FLEXIBLE CURRENT SENSOR CT9667-01, -02, -03 (5kA)

Voltage Connection

Current

500.00A

1.0000kA

5.0000kA

400.0V

1P2W

200.00kW

400.00kW

2.0000MW

1P3W

1P3W1U

3P3W2M

3P3W3M

400.00kW

800.00kW

4.0000MW

3P4W

600.00kW

1.2000MW

6.0000MW

Содержание PW3365













Отзывы: