manualshive.com logo in svg

Hioki IM7580, Инструкция по эксплуатации

Поделиться
Скачать
Hioki IM7580 Скачать руководство пользователя страница 305

297

Troubleshooting

13.3  Troubleshooting

For more information about external control, see “8 External Control” (p. 195).

Instrument malfunction

Symptoms

Check item or cause

Solution/Reference

The screen is not displayed 

even if the power supply is 

turned ON.

 

•

Is the power supply cord disconnected?

 

•

Is the power supply cord connected 

properly?

Confirm that the power cord is connected 

properly. (p. 20)

Keys do not function.

Are the keys locked?

Release the key lock. (p. 187)

Is the instrument operated remotely 

from an external device using the 

communication cable?

Switch to the local state.

See “Remote Mode” of the 

Communication Instruction Manual (LCR 

Application Disk).

A key other than the one 

pressed gets pressed.

Have you performed panel 

compensation?

Perform panel compensation. (p. 234)

Instrument doesn’t work.

You do not know how to 

operate this instrument.

Have you read the Instruction Manual?

Check the appropriate section of the 

Instruction Manual.

Are you using the instrument as part of 

an automated system?

Consult the administrator or the manager 

of the instrument or the automated 

system that contains the instrument.

Nothing is displayed on the 

screen.

 

•

Is the LCD display set to automatically 

turn off after a set time?

 

•

Is the instrument in the inactive state?

 

•

If you touch the touch panel, the back 

light will turn on again. (p. 182)

 

•

Cancel the inactive state. (p. 24)

Key response and screen 

refresh are slow.

Is the measurement value automatic 

output function enabled?

If the measurement value automatic 

output function is enabled, key response 

and screen refresh may become slow in 

order to give priority to measurement and 

measurement value output.

See Communications Commands  in the 

included LCR Application Disk.

13

Maintenance and Service

Содержание IM7580





















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды