Hioki IM7580 Скачать руководство пользователя страница 28

Страница: 28 / 340

Connecting the Power Cord

2.3 Connecting the Power Cord

Please read “Before turning ON the power” (p. 7), “Handling of cords and fixtures” (p. 8)

before connecting the power cord.

Connect the power cord to the power inlet on the instrument, and plug into an outlet.

Turn OFF the main power switch before disconnecting the power cord.

Check that the main power switch of the instrument is turned off.

Connect a power cord that is compatible with the line voltage to the power inlet on the

instrument (100 V to 240 V AC).

Rear

Plug the other end of the power cord into an outlet.

Содержание IM7580





















































































































































































































































































































































Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды

Hioki IM7580, Инструкция по эксплуатации

Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды