Hioki IM7580 Скачать руководство пользователя страница 15

Страница: 15 / 340

Operating Precautions

Warranty

Hioki disclaims responsibility for any direct or indirect damages that may occur if this instrument has been

combined with other devices by a systems integrator prior to sale or during resale.

Note.

Handling the instrument

DANGER

•

To avoid electric shock, do not remove the instrument’s case. The internal

components of the instrument carry high voltages and may become very hot

during operation.

•

Do not allow the instrument to get wet, and do not take measurements with wet

hands. This may cause an electric shock.

CAUTION

•

If the instrument exhibits abnormal operation or display during use, review the

information given in “13.3 Troubleshooting” (p. 297) and “13.4 Error Display” (p. 303)

before contacting your authorized Hioki distributor or reseller. Do not connect charged

capacitors, input voltage or current to the measuring terminals.The instrument will get

damaged.

•

To avoid damage to the instrument, protect it from physical shock when transporting

and handling. Be especially careful to avoid physical shock from dropping.

• This instrument is not designed to be entirely water- or dust-proof. Do not use it in an

especially dusty environment, nor where it might be splashed with liquid. This may

cause damage.

• Do not use excessive force on the touch panel, and do not use sharp objects that

could damage the touch screen.

•

Do not apply heavy downward pressure with the stand extended. The stand could be

damaged.

• To avoid damage to the instrument, do not short-circuit the terminal/ output terminal

and do not input voltage to the terminal/ output terminal.

•

After use, always turn OFF the power.

IMPORTANT

This instrument may cause interference if used in residential areas. Such use must be avoided

unless the user takes special measures to reduce electromagnetic emissions to prevent

interference to the reception of radio and television broadcasts.

Before turning ON the power

WARNING

•

Before turning the instrument on, make sure the supply voltage matches that

indicated on its power connector. Connection to an improper supply voltage

may damage the instrument and present an electrical hazard.

•

Be careful to avoid connecting the supply voltage improperly. Doing so may

damage the instrument’s internal circuitry.

•

To avoid electrical accidents and to maintain the safety specifications of this

instrument, connect the power cord provided only to a 3-contact (two-conductor

+ ground) outlet.

Appx.

Ind.

Содержание IM7580





















































































































































































































































































































































Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды

Hioki IM7580, Инструкция по эксплуатации

Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды