Hioki IM7580 Скачать руководство пользователя страница 32

Страница: 32 / 340

Turning the Power ON and OFF

2.6 Turning the Power ON and OFF

Connect the probe and test fixture before turning the main power on.

Rear

Front

Start button

Power switch

(main power)

Turning the main power ON

Turn the main power switch ON ( | ).

The start button on the front will light up in green.

(Lights up in green)

•

If the main power switch is turned OFF when

the instrument is in the inactive state, the

instrument will start up in the inactive state the

next time the main power switch is turned ON.

•

To measure to the degree of accuracy

mentioned in the specifications, allow a warm-

up time of 60 minutes or more after cancellation

of the inactive state.

Turning the main power OFF

Turn the main power switch OFF ( ).

The start button on the front will turn off.

(Turns OFF)

• When the power supply is interrupted by a

power failure etc, the instrument will recover to

the measurement mode used before the power

failure.

•

The instrument settings will be retained even if

the main power switch is turned OFF. (backup

function)

Turning to the inactive state

Press the start button on the front for

approximately 1 second in the main power ON

state.

The color of the start button on the front changes

to red in the inactive state.

(Lights up in red)

Canceling the inactive state

To measure to the degree of accuracy mentioned

in the specifications, allow a warm-up time of 60

minutes or more after cancellation of the inactive

state.

Press the start button on the front when the

instrument is in the inactive state.

The start button on the front will light up in green.

(Lights up in green)

What is inactive state?

The state in which the power supply of the instrument

is turned OFF.

(Only the circuit to turn ON the lamp of the start

button is active.)

If the instrument is not used for a long duration,

the internal battery must be charged. The required

charging time is at least 3 hours (recommended, 24

hours) after connecting the power supply and turning

ON the power of the instrument.

Содержание IM7580





















































































































































































































































































































































Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды

Hioki IM7580, Инструкция по эксплуатации

Результаты поиска

Содержание IM7580

Отзывы:

Бренды по названию

Популярные бренды