background image

 

 

Note1:  On  gasoline  machine  when  the  engine  is  cold,  once  it’s  ignited,  it’s 

possible to warm it up pressing the “WARM UP” button on the remote control, 
engine will run faster for 20 seconds. 
 

TRACKS MOVEMENTS 

All the outriggers  must be raised from the ground 

to move the tracks, otherwise the icon here on the 
left  side  will  be  displayed.  When  jib  is  closed  the 

tracks  could  be  moved  operating  from  the  ground 
or form the basket, otherwise it’s possible to move 

them  even  if  jib  is  opened  but  in  this  case  the 
basket  must  be  unloaded  from  its  support 
(LL1570), or be kept empty (LL1370) as reminded 
by the picture here on the right side. In this case, 

operator  must  drive  from  the  ground  keeping  the 
remote control on his hands.  

To move the tracks press the red joystick on the remote control.  
To open the jib (with basket off in the LL15) press the jib joystick.  
To  change  the  speed  it  has  to  be  used  button  n.5  of  remote 

control. 
Note2: Jib must be close to allow outriggers’ movements. 

Note3: In particular conditions, tracks’ speed could be automatically limited by 
speed control which prevent unsafe translations. 

 
OUTRIGGERS MOVEMENTS 

Machine must be perfectly closed and aligned to permit to 
move  the  outriggers,  so  all  the  arms  and  the  jib  closed 

and  aerial  part  rotated  as  indicated  by  the  alignment 
arrows  (see  picture  here  aside).  The  MACHINE  CLOSED 

AND  ALIGNED  icon  (see  the  picture  below)  indicates  the 
closed and aligned condition. To move the outriggers the 

remote control could be in the basket support or operator 
can keep it in his hands also standing at the ground. 
 
 
 

 
 

 

 

 
 

 
AUTOMATIC STABILIZATION: 

To  stabilize  the  machine  automatically  the  machine  must  be  closed  aligned. 
Keeping  pressed  the  green  button  (n.7)  on  the  remote  control  the  machine 

starts  the  automatic  stabilization  procedure.  That  procedure  will  be  complete 
only when the display will show the OK with the MACHINE STABILIZED icon as 

ALIGNMENT 

ARROWS 

MACHINE 

CLOSED AND 

ALIGNED 

ICON ON THE 

DISPLAY 

PHOTOCELLS SYSTEM 

DETECTS THE CLOSE 

AND ALIGNED 

CONDITION OF THE 

MACHINE 

UNLOAD 

THE 

BASKET 

FROM ITS 

SUPPORT 

(LL1570) 

RAISE THE 

OUTRIGGERS 

FROM THE 

GROUND 

BASKET MUST 

BE EMPTY 

(LL1370)  

Содержание LIGHTLIFT 15.70 PERFORMANCE

Страница 1: ...d be ignited by pressing the relevant buttons on the remote control see picture above Miniexcavators Undercarriages Minidumpers Skid Steer Loaders Aerial Platforms PRESS AND RELEASE REMOTE CONTROL EMERGENCY STOP BUTTON FIPE131521701 GASOLINE ENGINE WARM UP EMERGENCY STOP BUTTON GRAVITY EMERGENCY DESCENT AUTOMATIC OUTRIGGERS RETRACTION LEFT TRACK 1st CYLINDER JIB TURRET ROTATION RIGHT TRACK 2nd CYL...

Страница 2: ...vements Note3 In particular conditions tracks speed could be automatically limited by speed control which prevent unsafe translations OUTRIGGERS MOVEMENTS Machine must be perfectly closed and aligned to permit to move the outriggers so all the arms and the jib closed and aerial part rotated as indicated by the alignment arrows see picture here aside The MACHINE CLOSED AND ALIGNED icon see the pict...

Страница 3: ... when the MACHINE STABILIZED icon appears in position 5 of the display If one stabilization condition is missing when a joystick is moved the display indicates the missing condition with FAIL as follows ST X FAIL indicates that outrigger n X is not touching the ground INCL FAIL means that the machine is not levelled within the inclination clearance LOAD FAIL means that basket is overloaded more th...

Страница 4: ...n the turret looking at the yellow arrows Than the outriggers could be lifted and the tracks moved LIST OF DISPLAY ICONS Tracks maximum speed 12V Battery voltage low Insert the controller into its place and stabilize the machine from the basket Not allowed movement open the 2nd cylinder ...

Отзывы: