HIMA HIMatrix F60 DI 32 01 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 38

HIMA HIMatrix F60 DI 32 01 Скачать руководство пользователя страница 12

3 Product Description

DI 32 01

Page 12 of 38

HI 800 203 E Rev. 1.00

EMERGENCY STOP 1
EMERGENCY STOP 2

EMERGENCY STOP devices in
accordance with EN 60947-5-1 and
EN 60947-5-5

Figure 1:

Line Control

The device pulses the pulsed outputs to monitor the wires to the digital inputs. To do so,
configure the

Value [BOOL] ->

system variable in SILworX or the

DO[01].Value

system

signal in ELOP II Factory

.

The variables for the pulsed outputs must begin with channel 1

and reside in direct sequence, one after the other.

If the following faults occur, the

FAULT

LED located on the front plate of the controller

blinks, the inputs are set to low level and an (evaluable) error code is created:

Cross-circuit between two parallel lines,

Improper connections of two lines (e.g., TO 2 to DI 3),

Earth fault of a line (with earthed ground only),

Open-circuit or open contacts, i.e., including when one of the two EMERGENCY STOP

switches mentioned above has been engaged, the

FAULT

LED blinks and the error

code is created.

For more information on how to configure line control in the user program, refer to the
HIMatrix Engineering Manual.

«
...
10
11
12
13
14
...
»

Содержание HIMatrix F60 DI 32 01







































Отзывы:

Нет отзывов