background image

14

7. Operation

7.2.1 Symbols displayed

Temperature too high

> +50 °C (122 °F)

Action:

Allow the range meter to cool
down.

Temperature too low

< -10 °C (14 °F)

Action:

Warm up the range meter.

Unfavourable signal 
conditions

Insufficient reflected laser light

Action:

– Keep the measuring 

distance > 50 mm (2 inch)
from the front edge.

– Clean the lens.
– Take a measurement from

another surface or use the
target plate PDA 50.

Ambient light at target too
bright Action:

– Shade the target from bright

light or use the target plate
PDA 50.

Laser switched on

– moving dashed line  

Display reference status 

– Front edge
– Rear edge
– Spike
– Spike (flashing) – adds

automatically 1.270 m / 50
inch to measurements

Battery status

– 4 segments = 100% full
– 3 segments = 75% full
– 2 segments = 50% full
– 1 segment = 25% full
– 0 segments = empty

Batteries empty

Action:

– Replace batteries.
– Re-charge rechargeable

batteries 

Menu activated

Line with MIN distance
(shortest distance)

Line with MAX distance
(longest distance)

Display distances differences

– Difference between MAX

and MIN. distances

Historical data mode active

– Display the previous 5 

measurements or complete
functions results including
graphics

General hardware error

Switch the range meter Off
and then back On. If the error
persists, notify the local Hilti
service centre.

Indirect distance 
measurement

Switches between two
options:
– Single rectangular 

triangle

– Double rectangular 

triangles

Volume measurement active

Area measurement active

Printed: 07.07.2013 | Doc-Nr: PUB / 5070013 / 000 / 00

Содержание PD 32



































Отзывы: