![background image](http://html.mh-extra.com/html/hilti/dd-30-w/dd-30-w_original-operating-instructions_2135234046.webp)
38
English
WARNING
Risk of accident!
When drilling penetrations through walls or floors/ceilings, the core or fragments of
material may drop out and fall down on the other side.
▶
Take the necessary safety precautions on the other side of the wall or below the floor/ceiling before
drilling penetrations.
WARNING
Risk of injury due to flying fragments!
Drilling may cause hazardous flying fragments. Flying
fragments present a risk of injury to the body and eyes.
▶
Wear eye protection, protective clothing and a hard hat.
WARNING
Risk of injury.
The machine and the drilling operation generate noise. Exposure to noise can lead to
hearing loss.
▶
Wear ear protectors.
6.1 Hand-guided drilling
WARNING
Risk of electric shock!
If the machine is used for hand-guided drilling in an upwards direction without
the necessary safety precautions, water may enter the machine and present a risk of electric shock.
▶
When carrying out hand-guided drilling in an upwards direction, always use a water collection
system with a wet/dry industrial vacuum cleaner and the spray guard.
WARNING
Danger of electric shock!
Use of the wrong sealing ring when drilling overhead may cause water to
find its way into the interior of the diamond core drilling machine.
▶
Always use a sealing ring of the same diameter as the core bit.
1. Plug the drilling machine’s supply cord into a power outlet or, if using a vacuum cleaner, into the power
outlet on the all-purpose vacuum cleaner (if the vacuum cleaner is equipped with a power outlet).
2. If using a vacuum cleaner, plug the vacuum cleaner supply cord into the electric supply socket and set
the switch on the vacuum cleaner to the
AUTO
or
ON
position (i.e. the
I
position).
3. Switch on the ground fault circuit interrupter (PRCD) (see → page 37).
Note
In
AUTO
mode, the vacuum cleaner starts automatically with a delay after switching on the drilling
machine. When in
AUTO
mode the vacuum cleaner continues to run for a short time after the
drilling machine is switched off, before switching itself off automatically. When set to
ON
or
I
, the
vacuum cleaner requires to be switched on and off manually.
4. Mark the center of the hole to be drilled with a cross. The lines of the cross should be longer than the
diameter of the water collector.
Note
The water collector has four protruding marks that can be aligned with the cross.
5. Press the drilling machine’s control switch and hold it in this position. Set the water regulation lever to
the desired water flow rate and then release the control switch.
Note
The water supply (water on/off) is controlled automatically by the drilling machine’s control switch.
The water flow rate can be preset by turning the water regulating lever before starting drilling or
regulated while drilling is in progress (minimum water flow rate when the regulating lever is in the
“closed” position is approx. 0.3 l/min).
6. Position the water collector carefully at the position where the hole is to be drilled, without bringing the
core bit into contact with the working surface.
7. Bring the four marks on the water collector into alignment with the lines marking the center of the hole to
be drilled.
Printed: 20.12.2016 | Doc-Nr: PUB / 5283477 / 000 / 03
Содержание DD 30-W
