background image

Fig. 11  Rear load door removal

Rear Load Doors

1. 

Remove the rear sliding doors on the back of the case 
and clean. To remove: push up and pull out (Fig. 11).         

Note: The same applies for optional rear lower storage 
doors (RRS/DRS).

2. 

Use a spray bottle fi lled with an approved mild detergent 
and warm water.

3. 

Use a clean, disposable cloth (approved item) to thorough-
ly clean all areas of the case.

4. 

Wipe down doors with a clean, disposable cloth (approved 
item).

5. 

Place the cleaned doors on a clean sanitized surface until 
they are dry.

CASE CLEANING

A periodic cleaning schedule should be established to maintain 
proper  sanitation,  insure  maximum  operating  efficiency,  and  
avoid the corrosive action of food fluids on metal parts that are 
left on for long periods of time. We recommend that all heat-
ed surfaces be kept clear of excess food daily and a complete 
cleaning take place once a week. Further suggestions for case 
cleaning include the following:

• 

To avoid shock hazard, be sure all electrical power is turned 
off  before  cleaning.  In  some  installations,  more  than  one 
disconnect switch may have to be turned off to completely 
de-energize the case.

• 

Allow  cases  to  be  turned  off  long  enough  to  cool  before 
starting the cleaning process.

• 

Clean from top to bottom when cleaning the display case to 
avoid cross contamination.

• 

If  any  potentially  harmful  cleaners  are  used,  be  certain 
to  provide  a  temporary  separator  (e.g.,  cardboard,  plastic 
wrap,  etc.)  between  those  cases  that  are  being  cleaned 
and those that may still contain product.

• 

Avoid spraying any cleaning liquids directly on the electrical 
connections,  steam  cleaning  or  using  excessive  amounts 
of water.

• 

If  the  case  is  equipped  with  doors  be  sure  to  leave  them 
open until the case is completely dry.

• 

Remove  toekick  and  clean  underneath  the  case  with  a 
broom and a long-handled mop. Use warm water and a dis-
infecting cleaning solution when cleaning underneath the 
cases. 

     

D A N G E R

 

SHOCK HAZARD

Always disconnect power to case when servicing 
or cleaning.  Failure to do so may result in serious 
injury or death.

     

W A R N I N G

Always let the case cool before cleaning. Failure 
to do so may result in sub-standard operation 
and increased chances of safety issues/injury.

 

TECHNICAL REFERENCE

CASE CLEANING

16

Содержание DELI




























Отзывы: