Hill-Rom 305 Manual Bed страница 81 Скачать руководство пользователя

Страница: 81 / 176

4.13 Head or Knee Crank Rod and Drive Screw Assembly (Manual Model Only)

Chapter 4: Removal, Replacement, and Adjustment Procedures

Hill-Rom® Basic Care™ Bed, Hill-Rom® 305 Manual Bed,

Page 4 - 29

Hill-Rom® 405 Electric Bed Service Manual (MAN336 REV 2)

4.13 Head or Knee Crank Rod and Drive Screw Assembly (Manual

Model Only)

Tools required:

Small screwdriver

17 mm wrench

17 mm socket

Ratchet

Removal

1. Raise the knee section and head section to their highest positions.

2. Lift the foot section of the sleep surface, and fold it back toward the head

section.

NOTE:

If either of these sections cannot be raised, this procedure can be done from
underneath the foot end.

WARNING:

Attach the foot section to the head section. Failure to do so could cause
injury.

3. Use straps to attach the foot section to the head section.

4. Remove the footboard (A) from the bed frame (B) (see figure 4-13 on page

4-30).

5. Remove the plastic housing (C) from the crank handle assembly (D).

6. Lift the spring assembly (E) from the groove in the crank handle assembly

(D), and push the spring assembly (E) up the shaft of the crank handle
assembly (D).

7. Pull the crank handle assembly (D) out of the bed frame (B) until the crank

rod (F) releases from crank handle assembly (D).

8. Gently pry up on one side of the u-joint connection (G).

9. Gently pry up on the opposite side of the u-joint connection (G).

10. Remove the crank rod (F) from the drive screw assembly (H).

11. Remove the retaining ring (I), washer (L), and pin (K) that attach the drive

screw assembly (H) to the bed frame (B).

Содержание 305 Manual Bed

















































































































































































Результаты поиска

Содержание 305 Manual Bed

Отзывы:

Похожие инструкции для 305 Manual Bed

Бренды по названию

Популярные бренды

Hill-Rom 305 Manual Bed, Руководство по обслуживанию

Результаты поиска

Содержание 305 Manual Bed

Отзывы:

Похожие инструкции для 305 Manual Bed

Бренды по названию

Популярные бренды