background image

C

ASE

 C

ONNECTIONS

REFRIGERATION

As the diagram below indicates, the coil outlet hole is 
positioned forward on the right-hand side of the case, fully 
visible in front of the fan plenum.

The expansion valve and other controls - located on the 
left-hand side of the case - are accessible without lifting the 
fan plenum and may be reached by lifting the deck pans.

If it becomes necessary to penetrate the case bottom, be 
certain to seal it afterwards with canned-foam sealant and 
white RTV.

PLUMBING

The drain outlet is specially molded out of PVC material 
and is located in the center of the case for convenient ac-
cess.  The “P” trap, furnished with the case, is constructed 
of schedule 40 PVC pipe.   Care should be given to ensure 
that all connections are water-tight and sealed with the ap-
propriate PVC or ABS cement.

The drain lines can be run left or right of the tee with the 
proper pitch to satisfy local drainage requirements.  Since 
the kickplate is shipped loose with the case, you should 
have open access to the drain line area during installation.

35 1/16 in

 [89.1 cm]

**

39 3/8 in

 [99.9 cm]

41 5/16 in

 [104.9 cm]

31 11/16 in
 [80.5 cm]

FRONT OF CASE

C

L

1 1/2 in [3.8 cm] {END}

96 in [243.8 cm] (8' CASE)

8 11/16 in [22.1 cm]

 4 in[10.2 cm]

28 5/8 in

 [72.7 cm]

REFRIGERATION

REAR REFRIGERATION

(11 3/4" OFF OF FLOOR)

22 9/16 in [57.3 cm]

20 1/16 in [51.0 cm]

35 3/16 in

 [89.4 cm]

JUNCTION BOX
(STANDARD)

ELECTRICAL

1 1/2" PVC DRAIN

CONNECTION

33 9/16 in

 [85.3 cm]

MODEL

UPL-NRG

REMOVE THE SHIPPING BLOCKS THAT PROTECT THE 
REFRIGERATION LINES DURING SHIPMENT BEFORE 
OPERATING THE CASE.

REMOVE

If the kickplate has been installed, you will 

fi

 nd it very easy 

to remove.  Simply lift the kickplate up from the "J" rail and 
pull it out, away from the case.  See the Trim Out section 
on page 6.

ELECTRICAL

Electrical hookups are made to a junction box located at 
the bottom-left-front of the case.

For case-to-case wiring, run conduit between the junction 
boxes.  When connecting to the junction box on the bottom-
left side of the case, 

fi

 eld wiring should exit box from the 

right side (furthest away from case wiring) to allow more 
room inside for wiring connections.

     

C A U T I O N

If any brazing is necessary, place wet rags 

around the area to avoid tank damage.

7

Содержание UPL-NRG





















Отзывы: